HardLabs

FLIGHT CONTROLLER REV 2

justraven·FlightController·DESAIN PCB/FLIGHT_CONTROLLER_REV_2/FLIGHT_CONTROLLER_REV_2.kicad_pcb

FLIGHT CONTROLLER REV 2 PCB layout, top view — open source AVR/Arduino board by justraven

About the FLIGHT CONTROLLER REV 2 PCB

FLIGHT CONTROLLER REV 2 is an open source AVR/Arduino PCB design by justraven, published on GitHub under the MIT license. It is a 2-layer board measuring 78.7 × 99.1 mm, with 50 components from 19 distinct parts.

Its main chip is the ATmega328P-P, from the AVR/Arduino family. Other key parts include the FT232RL. By type, the board carries 14 capacitors, 13 connectors, 11 resistors, 5 diodes, 3 ICs and 2 crystals.

It belongs with the robotics & motion designs in this gallery.

From the project

Flight Controller PCB Design, Utilized ATMega328P. Compatible with MultiWii

Main components on the FLIGHT CONTROLLER REV 2

ATmega328P-PFT232RL

FLIGHT CONTROLLER REV 2 bill of materials (BOM)

50 components, 19 distinct parts — part numbers from the project's BOM.

QtyPartRefs
2
ATmega328P-P
U1, U3
1
FT232RL
U2
2
16 MHz
Y1, Y2
2
AVR-ISP-10
J1, J11
1
USB B
J2
4
Conn_01x03_Male
J3, J4, J5, J6
2
Conn_01x08_Female
J7, J8
1
FTDI BREAKOUT BOARD
J9
1
GPS INPUT
J10
1
TRANSMITTER_1
J12
1
TRANSMITTER_2
J13
2
SW_SPST
SW1, SW2
5
LED_Small
D1, D2, D3, D4, D5
4
22pF
C1, C3, C6, C8
7
100nF
C2, C4, C7, C9, C10, C11, C13
3
10uF
C5, C12, C14
2
10K
R1, R9
5
330R
R2, R3, R6, R7, R8
4
1K
R4, R5, R10, R11

FLIGHT CONTROLLER REV 2 design files

The KiCad project lives in the justraven/FlightController repository on GitHub; these links point at the commit this page was built from.

FLIGHT CONTROLLER REV 2: common questions

What microcontroller does the FLIGHT CONTROLLER REV 2 use?

The FLIGHT CONTROLLER REV 2 is built around the ATmega328P-P, from the AVR/Arduino family.

How big is the FLIGHT CONTROLLER REV 2 PCB?

The FLIGHT CONTROLLER REV 2 measures 78.7 × 99.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the FLIGHT CONTROLLER REV 2?

50 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the FLIGHT CONTROLLER REV 2 design files?

From the justraven/FlightController repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the FLIGHT CONTROLLER REV 2 design in my own project?

Yes, under the terms of its MIT license, which justraven chose for the repository.

Can I test firmware for the FLIGHT CONTROLLER REV 2 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in FlightController

Similar boards