NOS R-2R DAC

k16shikano·r2r-dac·kicad/DAC_CHANNEL_AXIAL/DAC_CHANNEL_AXIAL.kicad_pcb

NOS R-2R DAC PCB layout, top view — open source board by k16shikano
Simulate this board

About the NOS R-2R DAC PCB

NOS R-2R DAC is an open source PCB design by k16shikano, published on GitHub. It is a 4-layer board measuring 75 × 154 mm, with 122 components from 21 distinct parts.

Other key parts include the SN74LVC595APWR, TMUX1134PWR and OPA2192IDR. By type, the board carries 89 resistors, 22 capacitors, 7 ICs, 2 connectors and 1 inductor.

From the project

16ビットR-2RラダーによるDAコンバーターの設計

- TOSリンク(S/PDIF)からの44.1kHz入力 - ノンオーバーサンプリング - 左右2チャンネル - カードケージ構成(同一回路を1枚にまとめた SINGLEBOARD` あり)

DACCHANNEL と DACCHANNELAXIAL は同一の電気設計**で、S3 / S5 のどちらにも挿さります。 ラダー抵抗の実装方法だけが違います。

SINGLEBOARD もカードケージと同一の電気設計です。JBP とバックプレーンは無く、 R チャネルは 8xxx 参照(U8001 など)。±VREF はチャネルごとにローカル生成のままです。 信号層は F.Cu / In2.Cu / In3.Cu / B.Cu、In1.Cu と In4.Cu が GND ベタ(ラダー下は抜き)。 JRAW ヘッダ(J401 / J402` およびチャネル側)は基板上配線のタップとして残しています。

Main components on the NOS R-2R DAC

NOS R-2R DAC bill of materials (BOM)

122 components, 21 distinct parts — part numbers from the project's BOM.

QtyPartRefs
2
SN74LVC595APWR
U3001, U3002
4
TMUX1134PWR
U3003, U3004, U3005, U3006
1
OPA2192IDR
U3007
1
JRAW_1x3
J3001
1
JBP_2x18_AB
J3002
1
200R precision trimmer
RV3001
1
ferrite bead
FB3001
2
4.7uF
C3001, C3013
11
100nF
C3002, C3003, C3004, C3006, C3007, C3008, C3009, C3010 +3
3
100nF
C3005, C3011, C3015
1
4.7uF
C3014
3
1uF
C3017, C3018, C3051
2
1uF DNP
C3019, C3020
1
10k
R3001
18
100k
R3002, R3003, R3030, R3031, R3032, R3033, R3034, R3035 +10
16
150R
R3010, R3011, R3012, R3013, R3014, R3015, R3016, R3017 +8
1
100R
R3050
1
10.0k 0.1%
R3060
1
9.88k 0.1%
R3061
2
10R DNP
R3062, R3063
Show 1 more
QtyPartRefs
49
33.0k
R3101, R3102, R3103, R3104, R3105, R3106, R3107, R3108 +41

NOS R-2R DAC design files

The KiCad project lives in the k16shikano/r2r-dac repository on GitHub; these links point at the commit this page was built from.

NOS R-2R DAC: common questions

How big is the NOS R-2R DAC PCB?

The NOS R-2R DAC measures 75 × 154 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the NOS R-2R DAC?

122 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the NOS R-2R DAC design files?

From the k16shikano/r2r-dac repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the NOS R-2R DAC design in my own project?

The repository has no license, so all rights stay with k16shikano. Use it as a reference, and ask the author before reusing the design.

More boards in r2r-dac