HardLabs

RMK-complete LOWPRO

KarlPeter5039·RMK-final·PCB Misc/RMK-complete_LOWPRO.kicad_pcb

RMK-complete LOWPRO PCB layout, top view — open source AVR/Arduino board by KarlPeter5039

About the RMK-complete LOWPRO PCB

RMK-complete LOWPRO is an open source AVR/Arduino PCB design by KarlPeter5039, published on GitHub. It is a 2-layer board measuring 341.3 × 127 mm, with 77 components from 15 distinct parts.

Its main chip is the ProMicro, from the AVR/Arduino family. Other key parts include the 4PIN. By type, the board carries 34 switches, 34 diodes, 2 ICs, 2 resistors and 1 connector.

It belongs with the keyboards and displays & leds designs in this gallery.

From the project

Final iteration of the Reconfigurable Mechanical Keyboard including firmware and PCB files

Developed at Lehigh University for ECE 258 by Sumin Lim '23 and Karl Peter '23

While there have been many designs for modular keyboards, nothing out there really comes close to the practicality of our design. It will be different from generic commercial designs by adding additional peripherals including rotary encoders for analog input, a fully modular set up, and dedicated keyboard portions that can be connected and disconnected at any time.

RMK-complete LOWPRO, from the project README
From the project README

Main components on the RMK-complete LOWPRO

ProMicro4PIN

RMK-complete LOWPRO bill of materials (BOM)

77 components, 15 distinct parts.

QtyPartRefs
1
ProMicro
U1
1
4PIN
U2
1
Conn_01x04
J1
2
RotaryEncoder
ROT1, ROT2
1
R_Potentiometer
RV1
25
KEYSW
SW1, SW4, SW6, SW7, SW8, SW9, SW11, SW12 +17
2
KEYSW
SW2, SW35
2
KEYSW
SW3, SW34
2
KEYSW
SW5, SW10
2
KEYSW
SW20, SW33
1
KEYSW
SW31
1
SW_PUSH
SW_A1
30
D_Small
D1, D2, D3, D4, D5, D6, D7, D8 +22
4
VAL**
D32, D33, D34, D35
2
4.7k
R1, R2

RMK-complete LOWPRO design files

The KiCad project lives in the KarlPeter5039/RMK-final repository on GitHub; these links point at the commit this page was built from.

RMK-complete LOWPRO: common questions

What microcontroller does the RMK-complete LOWPRO use?

The RMK-complete LOWPRO is built around the ProMicro, from the AVR/Arduino family.

How big is the RMK-complete LOWPRO PCB?

The RMK-complete LOWPRO measures 341.3 × 127 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the RMK-complete LOWPRO?

77 components, from 15 distinct parts. The full bill of materials is listed on this page.

Where can I download the RMK-complete LOWPRO design files?

From the KarlPeter5039/RMK-final repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the RMK-complete LOWPRO design in my own project?

The repository has no license, so all rights stay with KarlPeter5039. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the RMK-complete LOWPRO without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in RMK-final

Similar boards