HardLabs

No fi delay

Krakenpine·krakenpine-synthing·no-fi-delay/no-fi-delay.kicad_pcb

No fi delay PCB layout, top view — open source AVR/Arduino board by Krakenpine

About the No fi delay PCB

No fi delay is an open source AVR/Arduino PCB design by Krakenpine, published on GitHub. It is a 2-layer board measuring 99.5 × 199.5 mm, with 80 components from 37 distinct parts.

Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the TL074 and TL072. By type, the board carries 34 resistors, 15 diodes, 11 capacitors, 7 connectors, 3 ICs and 3 switches.

It belongs with the audio designs in this gallery.

From the project

Synth modules?

Very low fidelity delay module in Kosmo format. Uses Arduino Nano 328P version with 2 kB ram. Install Mozzi library in Arduino IDE to use this. Files in KiCad format with schematic as pdf. Jack pcb and main pcb are connected with a 10 pin flat cable, like the one powering eurorack/kosmo modules. Don't accidentally connect power to that connector, otherwise this should be quite straightforward if you have build anything previously.

Main components on the No fi delay

TL074TL072Arduino_Nano_v3.x

No fi delay bill of materials (BOM)

80 components, 37 distinct parts.

QtyPartRefs
2
TL074
U1, U2
1
TL072
U3
1
Arduino_Nano_v3.x
A1
1
input
J1
1
length_cv
J2
1
feedback_cv
J3
3
Conn_02x05_Odd_Even
J4, J5, J6
1
output
J7
1
length_cv
RV1
1
fb_cv
RV2
1
delay_length
RV3
1
feedback
RV4
1
audio-in
RV5
1
delay-vol
RV6
1
gate
SW1
1
lofi-nofi
SW2
1
fullwet
SW3
4
LED
D1, D2, D3, D4
10
BAT42
D5, D6, D7, D8, D9, D10, D11, D12 +2
1
LED
D15
Show 17 more
QtyPartRefs
1
22n
C1
4
10n
C2, C5, C8, C9
2
100n
C3, C4
1
1n
C6
1
100p
C7
2
C_Polarized
C10, C11
1
10k
R1
1
499k
R2
2
3.9k
R3, R6
1
80k
R4
1
20k
R5
18
100k
R7, R8, R9, R10, R11, R12, R13, R15 +10
5
1k
R14, R26, R27, R33, R34
1
250k
R19
1
61.4k
R20
1
221k
R23
2
200k
R24, R25

No fi delay design files

The KiCad project lives in the Krakenpine/krakenpine-synthing repository on GitHub; these links point at the commit this page was built from.

No fi delay: common questions

What microcontroller does the No fi delay use?

The No fi delay is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.

How big is the No fi delay PCB?

The No fi delay measures 99.5 × 199.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the No fi delay?

80 components, from 37 distinct parts. The full bill of materials is listed on this page.

Where can I download the No fi delay design files?

From the Krakenpine/krakenpine-synthing repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the No fi delay design in my own project?

The repository has no license, so all rights stay with Krakenpine. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the No fi delay without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in krakenpine-synthing

Similar boards