Espxpansion
Las-Vejas·espxpansion·pcb/espxpansion.kicad_pcb
About the Espxpansion PCB
Espxpansion is an open source ESP32 PCB design by Las-Vejas, published on GitHub. It is a 2-layer board measuring 32 × 25.5 mm, with 10 components from 8 distinct parts.
Its main chip is the ESP32-C6-MINI-1, from the ESP32 family. By type, the board carries 5 resistors, 2 connectors, 2 capacitors and 1 IC.
From the project
This is an expansion module for the Hackxpansion console the consists of the ESP32-C6-MINI.
This is an expansion module for the Hackxpansion console the consists of the ESP32-C6-MINI.
The ESP can communicate to the Console using UART.

Main components on the Espxpansion
Espxpansion bill of materials (BOM)
10 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C6-MINI-1 | ESP32-C6-MINI-1 | U1 |
| 1 | N/A ~ | Male_Module | J1 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | 100NF 100nF | C_0402_1005Metric | C1 |
| 1 | 10UF 10uF | C_0402_1005Metric | C2 |
| 1 | 1k | R_0402_1005Metric | R1 |
| 1 | 20K 20k | R_0402_1005Metric | R2 |
| 3 | 10K 10k | R_0402_1005Metric | R3, R4, R5 |
Espxpansion design files
The KiCad project lives in the Las-Vejas/espxpansion repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/espxpansion.kicad_pcb
- Schematicpcb/espxpansion.kicad_sch
- BOMBOM.csv
Espxpansion: common questions
What microcontroller does the Espxpansion use?
The Espxpansion is built around the ESP32-C6-MINI-1, from the ESP32 family.
How big is the Espxpansion PCB?
The Espxpansion measures 32 × 25.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Espxpansion?
10 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Espxpansion design files?
From the Las-Vejas/espxpansion repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Espxpansion design in my own project?
The repository has no license, so all rights stay with Las-Vejas. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Espxpansion without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k