Usb c traffic light board
lemonhall·usb-c-traffic-light-board·kicad/usb_c_traffic_light_board.kicad_pcb
About the Usb c traffic light board
Usb c traffic light board is an open source WCH CH32/CH55x PCB design by lemonhall, published on GitHub. It is a 2-layer board measuring 14 × 57 mm, with 15 components from 10 distinct parts.
Its main chip is the CH552G, from the WCH CH32/CH55x family. By type, the board carries 7 resistors, 3 diodes, 3 capacitors, 1 IC and 1 connector.
From the project
这是一个用于替换原红绿灯小板的项目。目标是做一块新的 57mm x 14mm 电路板,通过 USB-C 供电,并让电脑通过 USB 串口控制红、黄、绿三颗灯。
这是一个用于替换原红绿灯小板的项目。目标是做一块新的 57mm x 14mm 电路板,通过 USB-C 供电,并让电脑通过 USB 串口控制红、黄、绿三颗灯。
- 完全替换原来的小电路板。 - 使用 USB-C 供电。 - 通过 USB-C 连接电脑,由电脑控制三颗灯。 - 电脑端识别为虚拟串口,方便脚本控制。 - 尽量避免飞线,最终装配时只使用这一块新板。
- 板长:57mm - 板宽:14mm - 当前板框已经按原板照片改成上下梯形端部和左右半圆避让槽。 - 三颗灯从上到下为:绿、黄、红;灯中心按从板底往上约 50mm、28mm、7mm 复核。 - 上螺丝孔直径 2mm,孔边离上端梯形窄边约 1mm。 - 下螺丝孔直径 2mm,孔中心离板顶约 33mm,位于板子左侧、靠近从下往上第二组避让槽。 - USB-C 目标位置对应原拨动开关穿出后壳的位置;原开关伸出背面约 10mm,开口宽度约 10mm。 - 注意:当前 KiCad 里 USBCReceptacleG-SwitchGT-USB-7025 是 right-angle 占位封装,不是最终可下单的立式背出 USB-C;最终必须按实物型号替换封装和 3D 机械模型。
Main components on the Usb c traffic light board
Usb c traffic light board bill of materials (BOM)
15 components, 10 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH552G | SOIC-16_3.9x9.9mm_P1.27mm | U1 |
| 1 | 背面USB-C | USB_C_Receptacle_G-Switch_GT-USB-7025 | J1 |
| 1 | 绿灯 | LED_1206_3216Metric | D1 |
| 1 | 橙灯 | LED_1206_3216Metric | D2 |
| 1 | 红灯 | LED_1206_3216Metric | D3 |
| 1 | 10uF | C_0805_2012Metric | C1 |
| 2 | 100nF | C_0603_1608Metric | C2, C3 |
| 3 | 1k | R_0603_1608Metric | R1, R2, R3 |
| 2 | 22R | R_0603_1608Metric | R4, R5 |
| 2 | 5.1k | R_0603_1608Metric | R6, R7 |
Usb c traffic light board design files
The KiCad project lives in the lemonhall/usb-c-traffic-light-board repository on GitHub; these links point at the commit this page was built from.
Usb c traffic light board: common questions
What microcontroller does the Usb c traffic light board use?
The Usb c traffic light board is built around the CH552G, from the WCH CH32/CH55x family.
How big is the Usb c traffic light board?
The Usb c traffic light board measures 14 × 57 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Usb c traffic light board?
15 components, from 10 distinct parts. The full bill of materials is listed on this page.
Where can I download the Usb c traffic light board design files?
From the lemonhall/usb-c-traffic-light-board repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Usb c traffic light board design in my own project?
The repository has no license, so all rights stay with lemonhall. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Usb c traffic light board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug WCH CH32/CH55x firmware against it before you order a PCB.
Similar boards
WCH CH32/CH55x
Ps2usb
rasteri
40 × 55 mm25 parts2LNo license428WCH CH32/CH55x
CH32X-48
rgoulter
224.6 × 74.2 mm112 parts2LNo license230WCH CH32/CH55x
CH32X-60-ANSI-Improved
rgoulter
285 × 94.2 mm149 parts2LNo license230WCH CH32/CH55x
CH32X-75
rgoulter
285 × 94.2 mm318 parts2LNo license230WCH CH32/CH55x
CH552-48
rgoulter
224.6 × 74.2 mm107 parts2LNo license230WCH CH32/CH55x
Webusb programmer rev6
laneboysrc
38 × 20 mm18 parts2LMIT87