Prostart
lorenzogalli-dev·Prostart·Hardware/PCB_ProStart_POC/PCB_ProStart_POC.kicad_pcb
About the Prostart PCB
Prostart is an open source ESP32 PCB design by lorenzogalli-dev, published on GitHub. It is a 2-layer board measuring 65.5 × 34 mm, with 8 components from 8 distinct parts.
Its main chip is the ESP32C3-SuperMini, from the ESP32 family. By type, the board carries 3 connectors, 2 capacitors, 1 IC, 1 buzzer and 1 switch.
It belongs with the iot & wireless, sensors and rf & radio designs in this gallery.
From the project
A low-cost, portable reaction-time and photo-finish system for track & field: a sensor unit on the starting block, a relay beside the finish line, and a phone app.
A low-cost, portable reaction-time and photo-finish system for track & field: a sensor unit on the starting block, a relay beside the finish line, and a phone app.
The start unit times the reaction locally, in microseconds, on its own clock. The radio chain only has to deliver the result and the start instant to the phone, which films the finish.
This repository contains the design and implementation of a two-part system:

Main components on the Prostart
Prostart bill of materials (BOM)
8 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32C3-SuperMini ESP32C3-SUPERMINI | DIP-ESP | U1 |
| 1 | LCD Display | PinSocket_1x08_P2.54mm_Vertical | J1 |
| 1 | IMU | PinSocket_1x06_P2.54mm_Vertical | J2 |
| 1 | IMU 2 | PinSocket_1x04_P2.54mm_Vertical | J3 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Button | SW_PUSH_6mm | SW1 |
| 1 | 100 nF | C_Disc_D3.8mm_W2.6mm_P2.50mm | C1 |
| 1 | 10UF 10uF | CP_Radial_D5.0mm_P2.00mm | C2 |
Prostart design files
The KiCad project lives in the lorenzogalli-dev/Prostart repository on GitHub; these links point at the commit this page was built from.
Prostart: common questions
What microcontroller does the Prostart use?
The Prostart is built around the ESP32C3-SuperMini, from the ESP32 family.
How big is the Prostart PCB?
The Prostart measures 65.5 × 34 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Prostart?
8 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Prostart design files?
From the lorenzogalli-dev/Prostart repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Prostart design in my own project?
The repository has no license, so all rights stay with lorenzogalli-dev. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Prostart without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k