BLARE-Alarm-Clock
maiver123·BLARE-Alarm-Clock
About the BLARE-Alarm-Clock PCB
BLARE-Alarm-Clock is an open source ESP32 PCB design by maiver123, published on GitHub. It is a 2-layer board measuring 59.5 × 39.5 mm, with 7 components from 4 distinct parts.
Its main chip is the MOUDLE-SEEEDUINO-XIAO-ESP32C3, from the ESP32 family. By type, the board carries 4 switches, 1 IC, 1 connector and 1 buzzer.
Main components on the BLARE-Alarm-Clock
BLARE-Alarm-Clock bill of materials (BOM)
7 components, 4 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MOUDLE-SEEEDUINO-XIAO-ESP32C3 | MOUDLE14P-SMD-2.54-21X17.8MM | U1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ3 |
| 4 | SW_Push | SW_PUSH_1P1T_6x3.5mm_H4.3_APEM_MJTP1243 | SW1, SW2, SW3, SW4 |
BLARE-Alarm-Clock design files
The KiCad project lives in the maiver123/BLARE-Alarm-Clock repository on GitHub; these links point at the commit this page was built from.
- LayoutBLARE.kicad_pcb
- SchematicBLARE.kicad_sch
BLARE-Alarm-Clock: common questions
What microcontroller does the BLARE-Alarm-Clock use?
The BLARE-Alarm-Clock is built around the MOUDLE-SEEEDUINO-XIAO-ESP32C3, from the ESP32 family.
How big is the BLARE-Alarm-Clock PCB?
The BLARE-Alarm-Clock measures 59.5 × 39.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the BLARE-Alarm-Clock?
7 components, from 4 distinct parts. The full bill of materials is listed on this page.
Where can I download the BLARE-Alarm-Clock design files?
From the maiver123/BLARE-Alarm-Clock repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the BLARE-Alarm-Clock design in my own project?
The repository has no license, so all rights stay with maiver123. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the BLARE-Alarm-Clock without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k