Plant watering system
marianobilli·plant-watering-system·hardware/kicad/plant_watering.kicad_pcb
About the Plant watering system PCB
Plant watering system is an open source ESP32 PCB design by marianobilli, published on GitHub under the MIT license. It is a 2-layer board measuring 143 × 112 mm, with 43 components from 23 distinct parts.
Its main chip is the YD-ESP32-23, from the ESP32 family. By type, the board carries 15 connectors, 12 resistors, 6 transistors, 6 diodes, 2 capacitors and 1 IC.
It belongs with the sensors designs in this gallery.
From the project
An arduino based system for automatic plant watering
An automated 6-plant watering system built on an ESP32-S3 (YD-ESP32-23), designed around the failures of typical DIY irrigation projects: corroding sensors, constant over-watering, no verification that watering worked.
- 6 independent stations: capacitive moisture sensor + 12 V peristaltic pump each - Two-phase watering cycle: dry cycle (check every N hours, water only at the minimum threshold) then incremental watering with soak time until the target is reached - Failsafes: a plant is stopped and flagged if moisture does not rise after a dose, if the sensor reads shorted/disconnected, or if…

Main components on the Plant watering system
Plant watering system bill of materials (BOM)
43 components, 23 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | YD-ESP32-23 | YD-ESP32-23 | U1 |
| 6 | IRLZ44N | TO-220-3_Vertical | Q1, Q2, Q3, Q4, Q5, Q6 |
| 1 | USB-C panel socket (V+/V-) | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | UI MODULE | UI_module_OLED_EC11 | J2 |
| 1 | Sensor1 (GND,VCC,DIS,OUT) | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J3 |
| 1 | Sensor2 (GND,VCC,DIS,OUT) | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J4 |
| 1 | Sensor3 (GND,VCC,DIS,OUT) | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J5 |
| 1 | Sensor4 (GND,VCC,DIS,OUT) | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J6 |
| 1 | Sensor5 (GND,VCC,DIS,OUT) | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J7 |
| 1 | Sensor6 (GND,VCC,DIS,OUT) | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J8 |
| 1 | Pump1_12V | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J9 |
| 1 | Pump2_12V | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J10 |
| 1 | Pump3_12V | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J11 |
| 1 | Pump4_12V | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J12 |
| 1 | Pump5_12V | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J13 |
| 1 | Pump6_12V | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J14 |
| 1 | Float switch (water level) | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J15 |
| 1 | MT3608 boost | MT3608_module | PS1 |
| 6 | 1N5819 | D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2, D3, D4, D5, D6 |
| 1 | 470uF/25V | CP_Radial_D8.0mm_P3.50mm | C1 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 470uF/10V | CP_Radial_D8.0mm_P3.50mm | C5 |
| 6 | 220 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R4, R5, R6 |
| 6 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R7, R8, R9, R10, R11, R12 |
Plant watering system design files
The KiCad project lives in the marianobilli/plant-watering-system repository on GitHub; these links point at the commit this page was built from.
Plant watering system: common questions
What microcontroller does the Plant watering system use?
The Plant watering system is built around the YD-ESP32-23, from the ESP32 family.
How big is the Plant watering system PCB?
The Plant watering system measures 143 × 112 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Plant watering system?
43 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Plant watering system design files?
From the marianobilli/plant-watering-system repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Plant watering system design in my own project?
Yes, under the terms of its MIT license, which marianobilli chose for the repository.
Can I test firmware for the Plant watering system without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k