FilamentSensor
matt-kiwi·FilamentSensor·KiCad/FilamentSensorProjectVeroBoard/FilamentSensorProjectVeroBoard.kicad_sch

About the FilamentSensor PCB
FilamentSensor is an open source ESP32 PCB design by matt-kiwi, published on GitHub. It is a board, with 23 components from 21 distinct parts.
Its main chip is the MCU ESP32-C3 Mini, from the ESP32 family. Other key parts include the DC-DC_Mini560 5V and PhotoMOS. By type, the board carries 13 connectors, 4 resistors, 3 ICs and 3 switches.
It belongs with the audio, iot & wireless and sensors designs in this gallery.
From the project
Used in the manufacturing process of making and recycling plastic. Specifically to detect if a strand of filament has been broken, then alert the operator with an audio alarm.
Used in the manufacturing process of making and recycling plastic. Specifically to detect if a strand of filament has been broken, then alert the operator with an audio alarm.
This device is dedicated to Bill and Eva of KiwiFil plastics in New Zealand. And their pioneering work with plastics recycling.
- Remove top lid with finger screws. - Pull out switch block assembly / cable entry plate. - Connect all 4 filament sensors using screw terminals, if a sensor is missing bridge Ground and Sensor input (Yellow). - Install switch block assembly aligning sensor cables in combe/clamp. - Install…
Main components on the FilamentSensor
FilamentSensor bill of materials (BOM)
23 components, 21 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MCU ESP32-C3 Mini | ESP32-C3-DevKitM-1 | U1 |
| 1 | DC-DC_Mini560 5V | DC-DC Mini560 | U2 |
| 1 | PhotoMOS | U3 | |
| 1 | Power input | J1 | |
| 1 | NeoPixels JST-PH | J2 | |
| 1 | Audio JST-PH | J3 | |
| 2 | Power JST-PH | J4, J5 | |
| 1 | Sensor1 | J6 | |
| 1 | Sensor2 | J7 | |
| 1 | Sensor3 | J8 | |
| 1 | Sensor4 | J9 | |
| 1 | Jack-DC 12v | J10 | |
| 2 | 3Pin JST | J11, J13 | |
| 1 | RCA Jack Alarm 12v | J12 | |
| 1 | Power switch | SW1 | |
| 1 | Mode Switch Alarm | SW2 | |
| 1 | Mode Switch WiFi | SW3 | |
| 1 | 47K | R1 | |
| 1 | 10K | R2 | |
| 1 | 22K | R3 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | R680 | R4 |
FilamentSensor design files
The KiCad project lives in the matt-kiwi/FilamentSensor repository on GitHub; these links point at the commit this page was built from.
FilamentSensor: common questions
What microcontroller does the FilamentSensor use?
The FilamentSensor is built around the MCU ESP32-C3 Mini, from the ESP32 family.
How many components are on the FilamentSensor?
23 components, from 21 distinct parts. The full bill of materials is listed on this page.
Where can I download the FilamentSensor design files?
From the matt-kiwi/FilamentSensor repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the FilamentSensor design in my own project?
The repository has no license, so all rights stay with matt-kiwi. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the FilamentSensor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k