Aquarium water level monitor
mattmbyrne-cmyk·aquarium-water-level-monitor·pcb/kicad/Water_Level_Project.kicad_pcb
About the Aquarium water level monitor PCB
Aquarium water level monitor is an open source ESP32 PCB design by mattmbyrne-cmyk, published on GitHub under the MIT license. It is a 2-layer board measuring 89 × 81 mm, with 15 components from 7 distinct parts.
Its main chip is the ESP32_DevKit_30Pin, from the ESP32 family. By type, the board carries 6 diodes, 6 resistors, 2 connectors and 1 IC.
It belongs with the iot & wireless and sensors designs in this gallery.
From the project
ESP32-based ultrasonic water level monitoring system for aquarium sumps using the waterproof A02YYUW sensor, with custom 3D-printable mounting hardware and web-based monitoring.
An open-source aquarium sump water level monitoring system built around the DFRobot A02YYUW waterproof ultrasonic sensor and an ESP32 microcontroller. The project provides reliable, non-contact water level measurement while keeping all electronics safely away from the water.
The system is specifically designed for aquarium sump installations and includes custom 3D-printable hardware for both the sensor mount and controller enclosure. Real-time water level status is displayed locally using green, yellow, and red LEDs, with an audible alarm to warn when the water level falls below a…

Main components on the Aquarium water level monitor
Aquarium water level monitor bill of materials (BOM)
15 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32_DevKit_30Pin | ESP32_DevKit_30Pin_25.2mm | U1 |
| 1 | A02YYUW | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Buzzer | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 2 | Green | LED_D5.0mm | D1, D2 |
| 2 | Yellow | LED_D5.0mm | D3, D4 |
| 2 | Red | LED_D5.0mm | D5, D6 |
| 6 | 220R | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R4, R5, R6 |
Aquarium water level monitor design files
The KiCad project lives in the mattmbyrne-cmyk/aquarium-water-level-monitor repository on GitHub; these links point at the commit this page was built from.
Aquarium water level monitor: common questions
What microcontroller does the Aquarium water level monitor use?
The Aquarium water level monitor is built around the ESP32_DevKit_30Pin, from the ESP32 family.
How big is the Aquarium water level monitor PCB?
The Aquarium water level monitor measures 89 × 81 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Aquarium water level monitor?
15 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Aquarium water level monitor design files?
From the mattmbyrne-cmyk/aquarium-water-level-monitor repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Aquarium water level monitor design in my own project?
Yes, under the terms of its MIT license, which mattmbyrne-cmyk chose for the repository.
Can I test firmware for the Aquarium water level monitor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k