Motor redo
About the Motor redo PCB
Motor redo is an open source AVR/Arduino PCB design by maxsterl666, published on GitHub. It is a 2-layer board measuring 156 × 78.5 mm, with 13 components from 8 distinct parts.
Its main chip is the ARDUINO_NANO_V3.X, from the AVR/Arduino family. By type, the board carries 4 connectors, 4 capacitors, 4 resistors and 1 module.
From the project
Moonlit Surface MK1
Main components on the Motor redo
Motor redo bill of materials (BOM)
13 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ARDUINO_NANO_V3.X Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 1 | FADER_1 | PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | FADER_2 | PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | FADER_3 | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | FADER_4 | PinHeader_1x06_P2.54mm_Vertical | J4 |
| 4 | C | C_Disc_D5.1mm_W3.2mm_P5.00mm | C1, C2, C3, C4 |
| 3 | 1M | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R2, R3, R4 |
| 1 | 4.7K 1M | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R5 |
Motor redo design files
The KiCad project lives in the maxsterl666/MLSMK1 repository on GitHub; these links point at the commit this page was built from.
Motor redo: common questions
What microcontroller does the Motor redo use?
The Motor redo is built around the ARDUINO_NANO_V3.X, from the AVR/Arduino family.
How big is the Motor redo PCB?
The Motor redo measures 156 × 78.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Motor redo?
13 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Motor redo design files?
From the maxsterl666/MLSMK1 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Motor redo design in my own project?
The repository has no license, so all rights stay with maxsterl666. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Motor redo without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in MLSMK1
8 x 8 LED Matrix Display
193 × 63.5 mm68 parts2LNo license0
AVR/ArduinoKicad test redo
161.8 × 180 mm50 parts4LNo license0
Kicad test redo w MPR121
160 × 180 mm47 parts4LNo license0
AVR/ArduinoKicad test
179 × 68.3 mm46 parts4LNo license0
Button vu
160 × 149 mm19 parts2LNo license0
Oled
204.8 × 34.3 mm5 parts2LNo license0
Similar boards
AVR/ArduinoV4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoModuleV450
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoEasyduino Atmega
Hanqaqa
68.8 × 53.6 mm35 parts4LCERN-OHL-P-2.0746
AVR/ArduinoEasyduino Atmega Nano
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746
AVR/ArduinoUsbGpib
xyphro
54 × 15 mm21 parts2LMIT683
AVR/ArduinoLumberjack
peej
284.7 × 94.2 mm149 parts2LMIT402