SMBeeHive
milelo·SMBeeHiveKiCad
About the SMBeeHive PCB
SMBeeHive is an open source PCB design by milelo, published on GitHub under the CC-BY-4.0 license. It is a 2-layer board measuring 87.8 × 76 mm, with 13 components from 13 distinct parts.
By type, the board carries 8 connectors, 2 resistors, 1 jumper, 1 switch and 1 diode.
It belongs with the power & battery and usb & debug tools designs in this gallery.
From the project
KiCad 5 design for SMBeeHive programmer / dock PCB
Anybody making an [SMBee] needs access to a programmer.
This is a low cost custom programmer you can use to give an SMBee a one-time programme or develope custom LED sequences for it. It uses the cheap widely available USBASP ISP programming module that you can purchase and re-flash with the required [custom firmware][SMBeeHive USBASP firmware].
There are two associated GitHub repositories: The case / jig design and laser cutter PDF: [SMBeeHive case] The custom USBASP firmware and reprogramming instructions: [SMBeeHive USBASP firmware].

SMBeeHive bill of materials (BOM)
13 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RST | Pin-0906-1-15-20-7X-14-11-0 | J1-1 |
| 1 | NC | Pin-0906-1-15-20-7X-14-11-0 | J1-2 |
| 1 | CLK | Pin-0906-1-15-20-7X-14-11-0 | J1-3 |
| 1 | DAT | Pin-0906-1-15-20-7X-14-11-0 | J1-4 |
| 1 | GND | Pin-0906-1-15-20-7X-14-11-0 | J1-5 |
| 1 | PWR | Pin-0906-1-15-20-7X-14-11-0 | J1-6 |
| 1 | USBASP | Pin_Header_Straight_2x05_Pitch2.54mm | J2 |
| 1 | S10V2F12 | Pin_Header_Straight_1x04_Pitch2.54mm | J3 |
| 1 | PRGM Source | Pin_Header_Straight_1x03_Pitch2.54mm | JP1 |
| 1 | toggle-sleep | SW_1825910-6 | SW1 |
| 1 | STPS0520Z | D_SOD-123 | D1 |
| 1 | 220R | R_0805_HandSoldering | R1 |
| 1 | 10K | R_0805_HandSoldering | R2 |
SMBeeHive design files
The KiCad project lives in the milelo/SMBeeHiveKiCad repository on GitHub; these links point at the commit this page was built from.
- LayoutSMBeeHive.kicad_pcb
SMBeeHive: common questions
How big is the SMBeeHive PCB?
The SMBeeHive measures 87.8 × 76 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SMBeeHive?
13 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the SMBeeHive design files?
From the milelo/SMBeeHiveKiCad repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the SMBeeHive design in my own project?
Yes, under the terms of its CC-BY-4.0 license, which milelo chose for the repository.
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k