Uwb anchors mcu
About the Uwb anchors mcu PCB
Uwb anchors mcu is an open source STM32 PCB design by mit-pev, published on GitHub. It is a 2-layer board measuring 38 × 57 mm, with 36 components from 25 distinct parts.
Its main chip is the STM32F103C8T6, from the STM32 family. Other key parts include the FT232RL and TPS62172DSGT. By type, the board carries 13 capacitors, 8 resistors, 4 diodes, 3 ICs, 3 switches and 2 connectors.
Main components on the Uwb anchors mcu
Uwb anchors mcu bill of materials (BOM)
36 components, 25 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | FT232RL | SSOP-28_5.3x10.2mm_P0.65mm | U1 |
| 1 | STM32F103C8T6 | LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | TPS62172DSGT | WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm_ThermalVias | U3 |
| 1 | 8MHz | Crystal_SMD_Abracon_ABM7-2Pin_6.0x3.5mm | Y1 |
| 1 | USB_Micro | USB_Micro-B_Molex-105017-0001 | J1 |
| 1 | Conn_01x08 | JST_XH_S8B-XH-A_1x08_P2.50mm_Horizontal | J3 |
| 1 | SW_Slide_x02 | CAS-D20B1 | SW1 |
| 1 | RST | SW_SPST_EVPBF | SW2 |
| 1 | BUT | SW_SPST_EVPBF | SW3 |
| 1 | UART_TX | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | UART_RX | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3 |
| 1 | BOOT | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D5 |
| 1 | PWR | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D6 |
| 1 | 1A | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | FB1 |
| 1 | 2.2uH | L_Taiyo-Yuden_NR-30xx_HandSoldering | L1 |
| 1 | 10nF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C2 |
| 4 | 0.1uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C5, C7, C16, C17 |
| 1 | 4.7uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C8 |
| 3 | 1uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C9, C10, C12 |
| 2 | 22uF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C11, C13 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 18pF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C14, C15 |
| 2 | 100 | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R3 |
| 2 | 50 | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5, R10 |
| 3 | 100K | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R6, R7, R8 |
| 1 | 10K | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R9 |
Uwb anchors mcu design files
The KiCad project lives in the mit-pev/pev_hardware_pcb repository on GitHub; these links point at the commit this page was built from.
Uwb anchors mcu: common questions
What microcontroller does the Uwb anchors mcu use?
The Uwb anchors mcu is built around the STM32F103C8T6, from the STM32 family.
How big is the Uwb anchors mcu PCB?
The Uwb anchors mcu measures 38 × 57 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Uwb anchors mcu?
36 components, from 25 distinct parts. The full bill of materials is listed on this page.
Where can I download the Uwb anchors mcu design files?
From the mit-pev/pev_hardware_pcb repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Uwb anchors mcu design in my own project?
The repository has no license, so all rights stay with mit-pev. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Uwb anchors mcu without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in pev_hardware_pcb
Similar boards
STM32LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7k
STM32Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9k
STM32Type g
169 × 30 mm24 parts2LApache-2.02.9k
STM32Main panel
234 × 84 mm26 parts4LApache-2.02.9k
STM32Type a
150 × 30 mm14 parts2LApache-2.02.9k
STM32Type c
188 × 30 mm17 parts2LApache-2.02.9k