Window air vent
mmassico·window_air_vent·pcb/window_vent_ctrl.kicad_pcb
About the Window air vent PCB
Window air vent is an open source ESP32 PCB design by mmassico, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 70 × 50 mm, with 23 components from 19 distinct parts.
Its main chip is the Freenove ESP32-S3 Lite, from the ESP32 family. Other key parts include the TMC2209 module. By type, the board carries 10 resistors, 8 connectors, 2 ICs, 1 jumper, 1 diode and 1 capacitor.
It belongs with the robotics & motion designs in this gallery.
From the project
Sliding window air exchanger without heat recovery (3D models)
A demand-controlled window ventilator for one room. Two 80 mm fans move air through a foam window insert: one brings fresh air in, the other exhausts stale air. A single butterfly-damper housing closes both holes with one shaft, turned by a silent stepper motor. An ESP32 reads a CO₂ sensor and runs the fans and the damper.
There is no heat recovery: every litre of air exhausted is lost heat. In exchange it is simple, cheap and automatic. See the estimates below.

Main components on the Window air vent
Window air vent bill of materials (BOM)
23 components, 19 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Freenove ESP32-S3 Lite | Freenove_ESP32S3_Lite | U1 |
| 1 | TMC2209 module | TMC2209_StepStick | U2 |
| 1 | 12V IN | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | FAN 0 intake | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | FAN 1 exhaust | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | MOTOR | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | SCD40 | PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | AS5600 | PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | DS18B20 in | PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | DS18B20 out | PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | D1 bypass | PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | 1N5822 | D_DO-201AD_P5.08mm_Vertical_AnodeUp | D1 |
| 1 | 220uF 50V | CP_Radial_D10.0mm_P5.00mm | C1 |
| 4 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_Vertical | R1, R2, R3, R4 |
| 1 | 10k | R_DIN0207_P10.16mm_Flat_Tight | R5 |
| 1 | 1k | R_DIN0207_P10.16mm_Flat_Tight | R6 |
| 1 | 100k | R_DIN0207_P10.16mm_Flat_Tight | R7 |
| 1 | 22k | R_DIN0207_P10.16mm_Flat_Tight | R8 |
| 2 | 4.7k | R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_Vertical | R9, R10 |
Window air vent design files
The KiCad project lives in the mmassico/window_air_vent repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/window_vent_ctrl.kicad_pcb
- Schematicpcb/window_vent_ctrl.kicad_sch
Window air vent: common questions
What microcontroller does the Window air vent use?
The Window air vent is built around the Freenove ESP32-S3 Lite, from the ESP32 family.
How big is the Window air vent PCB?
The Window air vent measures 70 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Window air vent?
23 components, from 19 distinct parts. The full bill of materials is listed on this page.
Where can I download the Window air vent design files?
From the mmassico/window_air_vent repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Window air vent design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which mmassico chose for the repository.
Can I test firmware for the Window air vent without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k