HardLabs

PS2BaseMount NanoPi

MRKane05·PS2BaseMount

PS2BaseMount NanoPi PCB layout, top view — open source PIC board by MRKane05

About the PS2BaseMount NanoPi PCB

PS2BaseMount NanoPi is an open source PIC PCB design by MRKane05, published on GitHub. It is a 2-layer board measuring 238.3 × 209.8 mm, with 25 components from 24 distinct parts.

Its main chip is the PIC16F18876-I_PT, from the PIC family. Other key parts include the NanoPiDUO2, PJ30240, Audio_Left, Audio_Right and AudioAmp. By type, the board carries 9 ICs, 7 connectors, 4 modules, 2 resistors, 1 transistor and 1 diode.

From the project

The KiCad project for the base mount for the "Junkstation" PS2 portable project

This is a dump of the KiCad project for the Junkstation PS2 project I made a few years ago. I'm really just backing it up for prosperity. I'm taking no responsibility for this and it really should be used only as reference.

It's worth noting that there are a couple of mistakes on the board that I haven't fixed: -The Ethernet wiring for the Mango isn't correct, and troubleshooting it was exceedingly difficult, so much so that I didn't write it down when I got it right, I just put the lid on it -The Ethernet lines for the Mango shouldn't be pulled down to Ground but pulled to the "R0" pin on…

Main components on the PS2BaseMount NanoPi

NanoPiDUO2PJ30240Audio_LeftAudio_RightAudioAmpDMosfet_AO9926B5VBuckBoostPIC16F18876-I_PTXOST_Buttons

PS2BaseMount NanoPi bill of materials (BOM)

25 components, 24 distinct parts.

QtyPartRefs
1
NanoPiDUO2
U1
1
PJ30240
U2
1
Audio_Left
U3
1
Audio_Right
U4
1
AudioAmp
U5
1
DMosfet_AO9926B
U6
1
5VBuckBoost
U7
1
PIC16F18876-I_PT
U8
1
XOST_Buttons
U9
1
PS2AVPort_SideMount
M1
1
PS2AVPort
M2
1
TS_LFT
M3
1
TS_RHT
M4
1
2N7000
Q1
1
RJ45
J1
1
Conn_01x06_Female
J2
1
USB_B
J3
1
USB_A_Dual
J4
1
PS2_MemCardMount
P1
2
PS2_ControlMount
P2, P3
Show 4 more
QtyPartRefs
1
1N58XX
D1
1
10uF
C1
1
100K
R1
1
1K
R2

PS2BaseMount NanoPi design files

The KiCad project lives in the MRKane05/PS2BaseMount repository on GitHub; these links point at the commit this page was built from.

PS2BaseMount NanoPi: common questions

What microcontroller does the PS2BaseMount NanoPi use?

The PS2BaseMount NanoPi is built around the PIC16F18876-I_PT, from the PIC family.

How big is the PS2BaseMount NanoPi PCB?

The PS2BaseMount NanoPi measures 238.3 × 209.8 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the PS2BaseMount NanoPi?

25 components, from 24 distinct parts. The full bill of materials is listed on this page.

Where can I download the PS2BaseMount NanoPi design files?

From the MRKane05/PS2BaseMount repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the PS2BaseMount NanoPi design in my own project?

The repository has no license, so all rights stay with MRKane05. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the PS2BaseMount NanoPi without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

More boards in PS2BaseMount

Similar boards