PS2BaseMount
About the PS2BaseMount PCB
PS2BaseMount is an open source PIC PCB design by MRKane05, published on GitHub. It is a 2-layer board measuring 273 × 146 mm, with 86 components from 61 distinct parts.
Its main chip is the PIC16F18876-I_PT, from the PIC family. Other key parts include the OrangePiZero, PJ30240, Audio_Left, Audio_Right and PAM8403. By type, the board carries 26 ICs, 17 resistors, 10 capacitors, 9 connectors, 7 modules and 7 diodes.
From the project
The KiCad project for the base mount for the "Junkstation" PS2 portable project
This is a dump of the KiCad project for the Junkstation PS2 project I made a few years ago. I'm really just backing it up for prosperity. I'm taking no responsibility for this and it really should be used only as reference.
It's worth noting that there are a couple of mistakes on the board that I haven't fixed: -The Ethernet wiring for the Mango isn't correct, and troubleshooting it was exceedingly difficult, so much so that I didn't write it down when I got it right, I just put the lid on it -The Ethernet lines for the Mango shouldn't be pulled down to Ground but pulled to the "R0" pin on…
Main components on the PS2BaseMount
PS2BaseMount bill of materials (BOM)
86 components, 61 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | OrangePiZero | OrangePiZero | U1 |
| 1 | PJ30240 | AudioJack_PJ30240 | U2 |
| 1 | Audio_Left | JST_1.5_2Pin | U3 |
| 1 | Audio_Right | JST_1.5_2Pin | U4 |
| 1 | PAM8403 | so-16 | U5 |
| 1 | DS18B20 | TO-92_Inline | U6 |
| 5 | GNDMount | GND | U7, U16, U24, U25, U26 |
| 1 | PIC16F18876-I_PT | PIC16F18876-I_PT | U8 |
| 1 | XOST_Buttons | XOST_ButtonsV2 | U9 |
| 1 | RJ14K | RJ14K_Modified | U10 |
| 2 | 18650_BatteryMount | 18650_3xHolderV3 | U11, U12 |
| 1 | DPAD | DPad_Buttons | U13 |
| 1 | RumbleA | JST_1.5_2Pin | U14 |
| 1 | RumbleB | JST_1.5_2Pin | U15 |
| 1 | ScreenPWM | JST_1.5_2Pin | U17 |
| 1 | PIC_14 | DIP-14_W7.62mm_LongPads | U18 |
| 1 | PS2_RESET | GND | U19 |
| 1 | LM2596T-5 | TO-263-5_TabPin3 | U20 |
| 1 | GND_IN | MountPoint | U21 |
| 1 | BATT_IN | MountPoint | U22 |
Show 41 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 5vMount | MountPoint | U23 |
| 1 | PS2AVPort_SideMount | PS2_AVPort_Complete_MountSilk | M1 |
| 1 | PS2AVPort | PS2_AVPort_Complete | M2 |
| 1 | TS_LFT | JST_1.25_5Pin | M3 |
| 1 | TS_RHT | JST_1.25_5Pin | M4 |
| 1 | TRIGGERS_LFT | JST_1.25_3Pin | M5 |
| 1 | TRIGGERS_RIGHT | JST_1.25_3Pin | M6 |
| 1 | Fan | JST_1.5_2Pin | M7 |
| 5 | 2N7000 | 2N7000_HandSolder | Q1, Q3, Q4, Q5, Q6 |
| 1 | Q_NMOS_GDS | TO-220F-3_Vertical | Q2 |
| 2 | RJ45 | RJ45_Floating | J1, J5 |
| 2 | Conn_01x06_Female | PinHeader_1x06_P2.54mm_Horizontal | J2, J8 |
| 1 | USB_B | USB_A_Custom_Throughhole_MountGuide | J4 |
| 1 | DB15_Female_HighDensity | ScreenBoardArea | J6 |
| 1 | PS2_MemCardMount | PS2_MemCardMountPoints | P1 |
| 2 | PS2_ControlMount | PS2_BoardMountFootprint | P2, P3 |
| 1 | INTERACTION | SMT_2X4X3.5MM | SW1 |
| 1 | START | SquishyTact | SW2 |
| 1 | SELECT | SquishyTact | SW3 |
| 1 | DIODE | Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | D1 |
| 1 | LED_GREEN | LED_D3.0mm | D2 |
| 1 | LED_YELLOW | LED_D3.0mm | D3 |
| 1 | LED_RED | LED_D3.0mm | D4 |
| 1 | D_Schottky | Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | D5 |
| 1 | BATT_LED_A | LED_D3.0mm | D6 |
| 1 | BATT_LED_B | LED_D3.0mm | D7 |
| 1 | INDUCTOR_33uH | L_12x12mm_H8mm | L1 |
| 1 | 10U | C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C1 |
| 3 | 470n | C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C2, C3, C9 |
| 3 | C1u | C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C4, C5, C6 |
| 1 | CP_680uF | CP_Radial_D8.0mm_P2.50mm | C7 |
| 1 | C470u | CP_Radial_D8.0mm_P2.50mm | C8 |
| 1 | CP_220uF | CP_Radial_D8.0mm_P3.50mm | C10 |
| 2 | 100K | R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R1, R4 |
| 2 | 1K | R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R2, R6 |
| 1 | 4.7K | R_2010_5025Metric_Pad1.52x2.65mm_HandSolder | R5 |
| 1 | 4.7K | D_2010_5025Metric_Pad1.52x2.65mm_HandSolder | R7 |
| 2 | R220 | R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R8, R9 |
| 1 | 220 | R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R10 |
| 6 | R10K | R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R11, R12, R13, R17, R18, R19 |
| 2 | R100K | R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R14, R15 |
PS2BaseMount design files
The KiCad project lives in the MRKane05/PS2BaseMount repository on GitHub; these links point at the commit this page was built from.
- LayoutPS2BaseMount.kicad_pcb
PS2BaseMount: common questions
What microcontroller does the PS2BaseMount use?
The PS2BaseMount is built around the PIC16F18876-I_PT, from the PIC family.
How big is the PS2BaseMount PCB?
The PS2BaseMount measures 273 × 146 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PS2BaseMount?
86 components, from 61 distinct parts. The full bill of materials is listed on this page.
Where can I download the PS2BaseMount design files?
From the MRKane05/PS2BaseMount repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the PS2BaseMount design in my own project?
The repository has no license, so all rights stay with MRKane05. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the PS2BaseMount without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
More boards in PS2BaseMount
Similar boards
PICPslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7k
PICLens
ervanalb
80 × 80 mm53 parts4LNo license515
PICMicro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414
PICGB-LIVE32
Gekkio
51.4 × 61 mm46 parts4LCC-BY-4.0376
PICGB-MBCTEST
51.4 × 61 mm32 parts2LCC-BY-4.0376
PICGB-BENCH-G1
100 × 100 mm98 parts4LCC-BY-4.0376