Pinchy
mwezi2k8·pinchy·Wiring/receiver/pinchy_rx.kicad_sch

About the Pinchy PCB
Pinchy is an open source AVR/Arduino PCB design by mwezi2k8, published on GitHub. It is a board, with 23 components from 11 distinct parts.
Its main chip is the Arduino_UNO_R3, from the AVR/Arduino family. Other key parts include the L7805. By type, the board carries 8 capacitors, 5 modules, 4 ICs, 2 diodes, 1 connector and 1 battery holder.
It belongs with the robotics & motion designs in this gallery.
From the project
4 DOF robot arm (base, shoulder, elbow and a claw) that you drive with 2 joysticks
A joystick controlled robot arm that picks stuff up :D
Pinchy is a 4 DOF robot arm (base, shoulder, elbow and a claw) that you drive with 2 joysticks. The remote has an Arduino Nano that reads the sticks and sends the values over a 2 wire cable to an Arduino Uno in the base, which moves 4 MG90S servos. It can pick up a small cube (around 20 mm, 5-10 g) and drop it somewhere else.
Main components on the Pinchy
Pinchy bill of materials (BOM)
23 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | L7805 | U1, U2, U3, U4 | |
| 1 | Arduino_UNO_R3 | Arduino_UNO_R3 | A1 |
| 4 | Motor_Servo | M1, M2, M3, M4 | |
| 1 | Conn_01x02_Pin | J1 | |
| 1 | Battery | Arduino_UNO_R3 | BT1 |
| 1 | SW_SPST | SW1 | |
| 1 | D | D1 | |
| 1 | LED | D2 | |
| 4 | 0.01uf | C1, C2, C3, C4 | |
| 4 | 0.1uf | C5, C6, C7, C8 | |
| 1 | 330 | R1 |
Pinchy design files
The KiCad project lives in the mwezi2k8/pinchy repository on GitHub; these links point at the commit this page was built from.
- SchematicWiring/receiver/pinchy_rx.kicad_sch
Pinchy: common questions
What microcontroller does the Pinchy use?
The Pinchy is built around the Arduino_UNO_R3, from the AVR/Arduino family.
How many components are on the Pinchy?
23 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pinchy design files?
From the mwezi2k8/pinchy repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Pinchy design in my own project?
The repository has no license, so all rights stay with mwezi2k8. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Pinchy without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k