TCS3200-sensor kit

Nigh·TCS3200-sensor-kit·layout/TCS3200-TB.kicad_pcb

TCS3200-sensor kit PCB layout, top view — open source RP2040/RP2350 board by Nigh

About the TCS3200-sensor kit PCB

TCS3200-sensor kit is an open source RP2040/RP2350 PCB design by Nigh, published on GitHub under the MIT license. It is a 2-layer board measuring 38.1 × 44.2 mm, with 5 components from 4 distinct parts.

Its main chip is the RP2040-Zero-Lite, from the RP2040/RP2350 family. By type, the board carries 2 ICs, 2 test points and 1 capacitor.

It belongs with the sensors and displays & leds designs in this gallery.

From the project

基于 TCS3200 + RP2040 的屏幕光信号测量套件:RGB 波形、颜色校准与延迟点击测试,含 Linux 上位机、固件、PCB 和 3D 外壳设计。

本目录提供 TCS3200 Sensor Kit 的 KiCad 工程、原理图和 PCB 布局。设计文件由 KiCad 10.0 生成。

- TCS3200-TB.kicadpro:KiCad 工程入口。 - TCS3200-TB.kicadsch:原理图。 - TCS3200-TB.kicad_pcb:PCB 布局。 - PCB.jpg:PCB 预览图。

使用 KiCad 10.0 或支持该文件格式的版本打开 .kicadpro`,进入原理图或 PCB 编辑器。制板前运行电气规则检查(ERC)和设计规则检查(DRC),核对封装、板框、连接与制造要求,再导出生产文件。

连接定义见 固件接线说明。修改 GPIO 分配时,同步更新 firmware/src/sensor.h 和接线表;调整板形或接口位置时,核对 外壳设计。

TCS3200-sensor kit, from the project README
From the project README

Main components on the TCS3200-sensor kit

RP2040-Zero-Lite

TCS3200-sensor kit bill of materials (BOM)

5 components, 4 distinct parts.

QtyPartRefs
1
RP2040-Zero-Lite
U1
1
~
U2
2
TestPoint
TP1, TP2
1
0.1uF
C1

TCS3200-sensor kit design files

The KiCad project lives in the Nigh/TCS3200-sensor-kit repository on GitHub; these links point at the commit this page was built from.

TCS3200-sensor kit: common questions

What microcontroller does the TCS3200-sensor kit use?

The TCS3200-sensor kit is built around the RP2040-Zero-Lite, from the RP2040/RP2350 family.

How big is the TCS3200-sensor kit PCB?

The TCS3200-sensor kit measures 38.1 × 44.2 mm, has 2 copper layers and is 1.6234 mm thick.

How many components are on the TCS3200-sensor kit?

5 components, from 4 distinct parts. The full bill of materials is listed on this page.

Where can I download the TCS3200-sensor kit design files?

From the Nigh/TCS3200-sensor-kit repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the TCS3200-sensor kit design in my own project?

Yes, under the terms of its MIT license, which Nigh chose for the repository.

Can I test firmware for the TCS3200-sensor kit without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards