Stereo hat
noranraskin·stereo-hat·kicad/stereo.kicad_pcb
About the Stereo hat
Stereo hat is an open source Raspberry Pi PCB design by noranraskin, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 68 × 56 mm, with 51 components from 27 distinct parts.
Its main chip is the Raspberry_Pi_4, from the Raspberry Pi family. Other key parts include the TAS5756MDCAR and TPS54232DR. By type, the board carries 31 capacitors, 9 resistors, 5 inductors, 3 connectors, 2 ICs and 1 diode.
It belongs with the audio, dev boards & breakouts and power & battery designs in this gallery.
From the project
A small, power-efficient AirPlay 2 network amplifier. A custom stereo class-D amplifier HAT sits on a Radxa Zero 3E running NixOS and shairport-sync, so any Apple device (or anything that speaks AirPlay 2) can stream straight to a pair of passive speakers over Ethernet.
A small, power-efficient AirPlay 2 network amplifier. A custom stereo class-D amplifier HAT sits on a Radxa Zero 3E running NixOS and shairport-sync, so any Apple device (or anything that speaks AirPlay 2) can stream straight to a pair of passive speakers over Ethernet.
- SBC: Radxa Zero 3E. Small, low power, and has wired Ethernet. Any SBC with a Raspberry Pi-style 40-pin header and an I2S interface on the standard pins should work. - Amplifier: TI TAS5756M, a stereo I2S-input class-D amp with a built-in DAC and DSP. It receives audio over I2S and is configured over I2C. - Power: one 12–24…

Main components on the Stereo hat
Stereo hat bill of materials (BOM)
51 components, 27 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TAS5756MDCAR | SOP50P810X120-49N | IC1 |
| 1 | TPS54232DR | TI_SO-PowerPAD-8_ThermalVias | U2 |
| 1 | Raspberry_Pi_4 | PinHeader_2x20_P2.54mm_Vertical | J1 |
| 1 | DC-005-A200 | JACK_DC-005-A200_XNP | J2 |
| 1 | 2601-1106 | CONN3_2601-1106_WAG | J5 |
| 1 | B340 | D_SMA_Handsoldering | D1 |
| 1 | 6.8µH | L_Changjiang_FXL0630 | L1 |
| 1 | L | L_1008_2520Metric | L2 |
| 3 | L | L_1008_2520Metric_Pad1.43x2.20mm_HandSolder | L3, L4, L5 |
| 4 | 22µF | C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C1, C7, C17, C20 |
| 1 | 0.1µF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 1 | 10nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | 180pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4 |
| 1 | 10pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 1 | 47µF | C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C6 |
| 6 | 1µF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C11, C12, C13, C14, C23 |
| 4 | 2.2µF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9, C10, C15, C16 |
| 4 | 220µF | CP_Elec_10x10 | C18, C19, C21, C22 |
| 4 | 0.22µF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C24, C25, C30, C31 |
| 4 | 0.68µF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C26, C27, C28, C29 |
Show 7 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 665k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 84.5k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 3 | 150k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R8, R9 |
| 1 | 75k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | 10.2k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 1 | 1.96k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | 390k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
Stereo hat design files
The KiCad project lives in the noranraskin/stereo-hat repository on GitHub; these links point at the commit this page was built from.
- Layoutkicad/stereo.kicad_pcb
- Schematickicad/stereo.kicad_sch
Stereo hat: common questions
What microcontroller does the Stereo hat use?
The Stereo hat is built around the Raspberry_Pi_4, from the Raspberry Pi family.
How big is the Stereo hat?
The Stereo hat measures 68 × 56 mm, has 2 copper layers and is 1.600198 mm thick.
How many components are on the Stereo hat?
51 components, from 27 distinct parts. The full bill of materials is listed on this page.
Where can I download the Stereo hat design files?
From the noranraskin/stereo-hat repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Stereo hat design in my own project?
Yes, under the terms of its GPL-3.0 license, which noranraskin chose for the repository.
Can I test firmware for the Stereo hat without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507