Boost-Converter
omarothman2004·Boost-Converter·kicad/Boost Converter.kicad_pcb
About the Boost-Converter PCB
Boost-Converter is an open source PCB design by omarothman2004, published on GitHub under the MIT license. It is a 2-layer board measuring 50.3 × 39.8 mm, with 10 components from 10 distinct parts.
Other key parts include the LT1302. By type, the board carries 4 resistors, 2 capacitors, 1 IC, 1 connector, 1 diode and 1 inductor.
It belongs with the power & battery designs in this gallery.
From the project
A 12V, LT1302-based step-up DC-DC converter board made for efficient voltage boosting with optimized inductor selection and low-noise layout routing.
Main components on the Boost-Converter
Boost-Converter bill of materials (BOM)
10 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LT1302 | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm | U1 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | MBRS340 | ST_D_SMC | D1 |
| 1 | 3.3µ | L_1210_3225Metric | L1 |
| 1 | 0.01µ | C_0201_0603Metric | C1 |
| 1 | 100µ | C_0805_2012Metric | C2 |
| 1 | 86.6K 86.6k | R_0805_2012Metric | R1 |
| 1 | 10K 10k | R_0805_2012Metric | R2 |
| 1 | 20K | R_0201_0603Metric | R3 |
| 1 | 240 | R_0805_2012Metric | R4 |
Boost-Converter design files
The KiCad project lives in the omarothman2004/Boost-Converter repository on GitHub; these links point at the commit this page was built from.
Boost-Converter: common questions
How big is the Boost-Converter PCB?
The Boost-Converter measures 50.3 × 39.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Boost-Converter?
10 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Boost-Converter design files?
From the omarothman2004/Boost-Converter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Boost-Converter design in my own project?
Yes, under the terms of its MIT license, which omarothman2004 chose for the repository.
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k