Project-Nira
only-foss·Project-Nira·hardware/v1.5_esp32_sensor/Nira_Micro-Plastic_Detection_Sensor/Nira_Micro-Plastic_Detection_Sensor.kicad_sch
About the Project-Nira PCB
Project-Nira is an open source ESP32 PCB design by only-foss, published on GitHub under the MIT license. It is a board, with 7 components from 7 distinct parts.
Its main chip is the PC_FDC1004, from the ESP32 family. By type, the board carries 1 IC, 1 module, 1 diode, 1 capacitor and 1 resistor.
It belongs with the iot & wireless and sensors designs in this gallery.
From the project
Affordable open-hardware sensor to detect microplastics in water using ESP32 + FDC1004 capacitance sensing
Project Nira is an affordable (₹2500), portable impedance-based sensor designed to detect microplastics (<5mm) in water. It serves as a field-ready alternative to expensive lab spectrometers for schools and community groups.
1. Hardware: ESP32-S3 + ADS131M08 (24-bit ADC) + 316L stainless steel electrodes. 2. Firmware: ESP-IDF handling 1ksps data acquisition with BLE/WiFi streaming. 3. Software: Python-based pipeline for signal processing and real-time visualization.
Main components on the Project-Nira
Project-Nira bill of materials (BOM)
7 components, 7 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | PC_FDC1004 ESP32-DEVKIT-V1 | MODULE_ESP32_DEVKIT_V1 | U1 |
| 1 | Motor_DC | M1 | |
| 1 | ~ | FDC1004_v3 | |
| 1 | 3.3V 5.0v | V1 | |
| 1 | LED | D2 | |
| 1 | C_Trim_Differential | C1 | |
| 1 | R | R2 |
Project-Nira design files
The KiCad project lives in the only-foss/Project-Nira repository on GitHub; these links point at the commit this page was built from.
Project-Nira: common questions
What microcontroller does the Project-Nira use?
The Project-Nira is built around the PC_FDC1004, from the ESP32 family.
How many components are on the Project-Nira?
7 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Project-Nira design files?
From the only-foss/Project-Nira repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Project-Nira design in my own project?
Yes, under the terms of its MIT license, which only-foss chose for the repository.
Can I test firmware for the Project-Nira without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k