PX-CORE
OPRobots·PX-CORE·hardware/kicad_project/PX-CORE.kicad_pcb
About the PX-CORE PCB
PX-CORE is an open source ESP32 PCB design by OPRobots, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 50 × 34 mm, with 14 components from 10 distinct parts.
Its main chip is the ESP32_supermini, from the ESP32 family. By type, the board carries 3 connectors, 3 LEDs and 2 modules.
It belongs with the robotics & motion designs in this gallery.
From the project
Placa multiusos, pensada para casi cualquier tipo de robot
Es la placa principal de control común a todos nuestros kits PX. Está pensada para poder usarse en casi cualquier tipo de robot.

PX-CORE bill of materials (BOM)
14 components, 10 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | Conn_01x02_Socket | motor_pads | M1, M2 |
| 1 | Conn_01x03_Socket | PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | Conn_01x02_Socket | XT30 connector | J2 |
| 1 | Conn_01x07_Socket | PinHeader_1x07_P2.54mm_Vertical | J4 |
| 1 | ~ | SW_PUSH_6mm_H4.3mm | BTN1 |
| 1 | ~ | DC-DC_3.3 CN3903 | DC-DC_3.3 |
| 1 | ~ | ESP32_supermini | ESP32 |
| 2 | ~ | DIP-8_W7.62mm | PH1, PH2 |
| 1 | Conn_01x03_Socket | PinHeader_1x03_P2.54mm_Vertical | START1 |
| 3 | ~ | LED_D5.0mm-4_RGB_Staggered_Pins | LED1, LED2, LED3 |
PX-CORE design files
The KiCad project lives in the OPRobots/PX-CORE repository on GitHub; these links point at the commit this page was built from.
PX-CORE: common questions
What microcontroller does the PX-CORE use?
The PX-CORE is built around the ESP32_supermini, from the ESP32 family.
How big is the PX-CORE PCB?
The PX-CORE measures 50 × 34 mm, has 2 copper layers and is 1.29 mm thick.
How many components are on the PX-CORE?
14 components, from 10 distinct parts. The full bill of materials is listed on this page.
Where can I download the PX-CORE design files?
From the OPRobots/PX-CORE repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the PX-CORE design in my own project?
Yes, under the terms of its GPL-3.0 license, which OPRobots chose for the repository.
Can I test firmware for the PX-CORE without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k