Epilepsy-Electronics
pawel-dzialo·Epilepsy-Electronics·MCU_Prototype/MCU_Prototype.kicad_pcb
About the Epilepsy-Electronics PCB
Epilepsy-Electronics is an open source STM32 PCB design by pawel-dzialo, published on GitHub. It is a 4-layer board measuring 71.5 × 69.5 mm, with 30 components from 23 distinct parts.
Its main chip is the STM32L431RCT6, from the STM32 family. Other key parts include the LD1117S33CTR, BLUENRG-M0A and ADuM1200AR. By type, the board carries 13 capacitors, 8 connectors, 4 ICs, 2 switches, 1 fuse and 1 diode.
Main components on the Epilepsy-Electronics
Epilepsy-Electronics bill of materials (BOM)
30 components, 23 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LD1117S33CTR | SOT223 | U1 |
| 1 | BLUENRG-M0A | ST_SPBTLE | U2 |
| 1 | ADuM1200AR | SOIC127P600X175-8N | U3 |
| 1 | STM32L431RCT6 | LQFP-64_10x10mm_P0.5mm | U4 |
| 1 | UART | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Battery | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | SWD | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | USB_A | USBA | J4 |
| 1 | PIN1-PIN16 | PinHeader_2x08_P2.54mm_Vertical | J5 |
| 1 | PIN17-PIN32 | PinHeader_2x08_P2.54mm_Vertical | J6 |
| 1 | PIN33-PIN48 | PinHeader_2x08_P2.54mm_Vertical | J7 |
| 1 | PIN49-PIN64 | PinHeader_2x08_P2.54mm_Vertical | J8 |
| 1 | Fuse | Fuse_Rad | F1 |
| 1 | SW_DPDT_x2 | Switch | SW1 |
| 1 | SW_Push | Button | SW2 |
| 1 | LED | LED | D1 |
| 5 | 100n | C_0805_2012Metric | C1, C5, C6, C7, C8 |
| 1 | 10u | CP_Radial_D5.0mm_P2.00mm | C2 |
| 1 | 10n | C_0805_2012Metric | C3 |
| 4 | 4.7u | CP_Radial_D5.0mm_P2.00mm | C9, C10, C12, C13 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 0.1u | C_0805_2012Metric | C11 |
| 1 | 1u | CP_Radial_D5.0mm_P2.00mm | C15 |
| 1 | R_Small | R_0805_2012Metric | R1 |
Epilepsy-Electronics design files
The KiCad project lives in the pawel-dzialo/Epilepsy-Electronics repository on GitHub; these links point at the commit this page was built from.
Epilepsy-Electronics: common questions
What microcontroller does the Epilepsy-Electronics use?
The Epilepsy-Electronics is built around the STM32L431RCT6, from the STM32 family.
How big is the Epilepsy-Electronics PCB?
The Epilepsy-Electronics measures 71.5 × 69.5 mm, has 4 copper layers and is 4.69 mm thick.
How many components are on the Epilepsy-Electronics?
30 components, from 23 distinct parts. The full bill of materials is listed on this page.
Where can I download the Epilepsy-Electronics design files?
From the pawel-dzialo/Epilepsy-Electronics repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Epilepsy-Electronics design in my own project?
The repository has no license, so all rights stay with pawel-dzialo. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Epilepsy-Electronics without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k