7 open source boards using the ADuM1200AR
Real designs built with the ADuM1200AR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
EQMOD DIRECT Isolated
claudioarena
76.1 × 21.5 mm36 parts4LNo license3Pyblockplc topseite
pyplc
100.3 × 71.1 mm73 parts2LNo license2Pulser V2 HC Board
xy-kasumi
100 × 50 mm72 parts4LNo license0STM32
Epilepsy-Electronics
pawel-dzialo
71.5 × 69.5 mm30 parts4LNo license0AVR/Arduino
Pulser V2 HV Board
xy-kasumi
100 × 50 mm62 parts4LNo license0STM32
MCU Prototype
pawel-dzialo
71.5 × 69.5 mm30 parts4LNo license0FeatherVoltmeterPCBA
oihdesigns
23.5 × 51.1 mm28 parts4LNo license2
How designs wire the ADuM1200AR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ADuM1200AR connects to, and the resistors, capacitors and other passives placed on it.
- The VDD1 pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF.
- The VOB pin has a series resistor on 3 of 6 designs, most often 200 Ω (then 4.7 kΩ).
- The VOA pin has a series resistor on 3 of 6 designs, most often 200 Ω (then 75 kΩ).
- The VDD2 pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDD1pin 1 | Connected to: 5V 67% · a signal 33% |
|
| VIBpin 3 | Connected to: A connector 67% · not connected 17% |
|
| GND1pin 4 | Connected to: GND 67% · a signal 33% | — |
| GND2pin 5 | Connected to: GND 83% · a signal 17% | — |
| VOBpin 6 | Connected to: The microcontroller 33% · not connected 17% |
|
| VOApin 7 | Connected to: The microcontroller 33% |
|
| VDD2pin 8 | Connected to: VDD 67% · a signal 33% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EQMOD DIRECT Isolated by claudioarena, FeatherVoltmeterPCBA by oihdesigns, Pyblockplc topseite by pyplc and MCU Prototype by pawel-dzialo.
The ADuM1200AR in open source designs
The gallery holds 7 open source boards using the ADuM1200AR from 6 GitHub repositories; a typical one measures about 76.1 × 51 mm and carries around 36 components.
86% use four copper layers or more, and 0% carry an open source license.
The most starred is EQMOD DIRECT Isolated by claudioarena.
Parts used alongside the ADuM1200AR
Microcontrollers on boards using the ADuM1200AR
What boards using the ADuM1200AR are built for
ADuM1200AR: common questions
Where can I find a ADuM1200AR reference design?
Each of the 7 boards on this page is a real design using the ADuM1200AR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ADuM1200AR VDD1 pin?
The VDD1 pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the ADuM1200AR.
What resistor goes on the ADuM1200AR VOB pin?
The VOB pin has a series resistor on 3 of 6 designs, most often 200 Ω (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the ADuM1200AR.
What resistor goes on the ADuM1200AR VOA pin?
The VOA pin has a series resistor on 3 of 6 designs, most often 200 Ω (then 75 kΩ). Counted from the KiCad layouts of 6 open source designs using the ADuM1200AR.
What parts are used alongside the ADuM1200AR?
The BLUENRG-M0A, LD1117S33CTR and STM32L431RCT6 appear in the most repositories here.
Which microcontrollers do boards using the ADuM1200AR use?
Most are built on STM32 (2) and AVR/Arduino (1).
How big is a typical board using the ADuM1200AR?
The median is 76.1 × 51 mm, and 14% are two-layer designs.
What is the most popular open source board using the ADuM1200AR?
By GitHub stars, EQMOD DIRECT Isolated by claudioarena, with 3 stars.
Can I simulate one of these boards using the ADuM1200AR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.