BilgeAlarm
phorton1·Arduino-boat-bilgeAlarm·docs/kiCad/board/bilgeAlarm.kicad_pcb
About the BilgeAlarm PCB
BilgeAlarm is an open source ESP32 PCB design by phorton1, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 111.8 × 88.9 mm, with 54 components from 26 distinct parts.
Its main chip is the ESP32_DEV_0, from the ESP32 family. By type, the board carries 28 connectors, 12 resistors, 4 switches, 2 modules, 2 transistors and 2 diodes.
From the project
Second generation ESP32 based bilgeAlarm (previously "bilgePumpSwitch")
Home -- History -- Previous -- Design -- Hardware -- Software -- UI
The bilgeAlarm is the most important device I have created for my boat, Rhapsody. It is a device for monitoring the bilge pump(s) on the boat, sounding a loud alarm if the bilge pump runs too long, or too often. It is the result of almost sinking Rhapsody one time when the bilge pump ran, but could not be heard, until it burnt out and the boat took on 1000's of gallons of water, resulting in serious damage and a huge amount of repairs ... and time and money ... to fix the problems caused by the flooding.

Main components on the BilgeAlarm
BilgeAlarm bill of materials (BOM)
54 components, 26 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32_DEV_0 | myESP32DEV0 | U1 |
| 1 | BUCK01 | myMini360BuckConverter | M1 |
| 1 | SD_TYP0 | SDCardReader | M2 |
| 1 | IRLZ44N | myTO-220-3 | Q1 |
| 1 | BCS547 | my3pin | Q2 |
| 1 | BA_POWER | myTerminalBlock_5.08x02 | J1 |
| 1 | PUMPS | myTerminalBlock_5.08x03 | J2 |
| 1 | ALARM | myTerminalBlock_5.08x02 | J3 |
| 1 | LEDS | myPinSocket_1x03 | J6 |
| 1 | LEDS OUT | myPinSocket_1x03 | J7 |
| 1 | LEDS IN | myPinSocket_1x03 | J8 |
| 1 | LCD | myPinSocket_1x04 | J9 |
| 21 | AUX | my1pin | J21, J22, J23, J24, J25, J26, J27, J28 +13 |
| 1 | RELAY | myRelay | K1 |
| 1 | POWER | mySwitchToggleSPDT | SW1 |
| 1 | BUTTON1 | myButton | SW2 |
| 1 | BUTTON2 | myButton | SW3 |
| 1 | BUTTON3 | myButton | SW4 |
| 1 | 1N5818 | myDiodeSchotsky | D1 |
| 1 | 1N4005 | myDiodeSchotsky | D2 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 47uf | CP_my100uf | C1 |
| 1 | 10uf | CP_my10uf | C2 |
| 4 | 10K | myResistor | R1, R6, R7, R11 |
| 1 | 220 | myResistor | R2 |
| 3 | 4.7K | myResistor | R3, R4, R5 |
| 4 | 1K | myResistor | R8, R9, R10, R13 |
BilgeAlarm design files
The KiCad project lives in the phorton1/Arduino-boat-bilgeAlarm repository on GitHub; these links point at the commit this page was built from.
BilgeAlarm: common questions
What microcontroller does the BilgeAlarm use?
The BilgeAlarm is built around the ESP32_DEV_0, from the ESP32 family.
How big is the BilgeAlarm PCB?
The BilgeAlarm measures 111.8 × 88.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the BilgeAlarm?
54 components, from 26 distinct parts. The full bill of materials is listed on this page.
Where can I download the BilgeAlarm design files?
From the phorton1/Arduino-boat-bilgeAlarm repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the BilgeAlarm design in my own project?
Yes, under the terms of its GPL-3.0 license, which phorton1 chose for the repository.
Can I test firmware for the BilgeAlarm without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Arduino-boat-bilgeAlarm
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k