SUNDIAL

photovoltaic-art·SUNDIAL·hardware/carrier/carrier.kicad_sch

This repository ships a schematic but no board layout.

About the SUNDIAL PCB

SUNDIAL is an open source ESP32 PCB design by photovoltaic-art, published on GitHub. It is a board, with 82 components from 64 distinct parts.

Its main chip is the PinSocket_1x15_P2.54mm_Vertical, from the ESP32 family. Other key parts include the DS3231SN (or RV-3028-C7, firmware change), INA180A3 (gain 100) and MCP1416 (or TC4427A class). By type, the board carries 20 resistors, 15 connectors, 11 test points, 11 capacitors, 7 diodes and 4 ICs.

It belongs with the test & measurement designs in this gallery.

From the project

photovoltaic art

A KiCad schematic for the carrier board, generated from the specification in CARRIER.md.

Everything needed is linked from this page:

1. Specification: CARRIER.md (also as a PDF): what the board does, every part with its rating, layout rules, bench test. 2. Schematic PDF (A1): the full drawing, with notes on current paths and measurement ranges. 3. Bill of materials: bom.csv: references, values and ratings, footprints, fitted or not. 4. KiCad files: carrier.kicadpro, carrier.kicadsch, and the netlist with footprints carrier.net. Download the whole folder to open the project. 5. Design…

Main components on the SUNDIAL

DS3231SN (or RV-3028-C7, firmware change)INA180A3 (gain 100)MCP1416 (or TC4427A class)

SUNDIAL bill of materials (BOM)

82 components, 64 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
DS3231SN (or RV-3028-C7, firmware change)
U1
1
INA180A3 (gain 100)
U2
1
MCP1416 (or TC4427A class)
U3
1
Load switch 5 V >=1 A, active-high EN, soft start (AP22804AW5 / TPS22918 class)
U4
1
N-MOSFET >=60 V (>=100 V if D6 fitted) >=20 A Rds(on)<=20 mOhm @4.5 V
Q1
1
PANEL+ / PANEL- (>=15 A, 4-6 mm2)
J1
1
BUCK IN + / -
J2
1
BUCK OUT + / - (set 5.0 V)
J3
1
DS18B20: 3V3 / DATA / GND
J4
1
Optional 2nd probe
J5
1
Supercap 2.7 V 10 F (upper)
J6
1
Supercap 2.7 V 10 F (lower)
J7
1
microSD push-push with detect (Hirose DM3AT)
J8
1
Spare: 3V3 GND 32 33 36 26 27 13 14
J9
1
UART: 3V3 GND RX2(16) TX2(17)
J10
1
5V / 5V SW / 3V3 / GND
J11
1
AUX + / - (>=15 A)
J12
1
I2C: 3V3 GND SDA SCL
J13
1
ESP32 left row: EN,36,39,34,35,32,33,25,26,27,14,12,13,GND,VIN
J14
1
ESP32 right row: 23,22,1,3,21,19,18,5,17,16,4,2,15,GND,3V3
J15
Show 44 more
QtyPartRefs
1
CR2032 holder (no charging)
BT1
1
2 A slow-blow
F1
1
PTC 0.5 A hold
F2
1
PTC 0.2 A hold
F3
1
ATO blade holder, fuse NOT fitted (<=3 A on v1; 9 A only with D5 heatsink)
F4
4
M3
H1, H2, H3, H4
1
Jumper: remove = sun sensor off
JP1
1
5m 1% 2512 >=2 W
RSH1
1
DNP (option: 2x 10m)
RSH2
1
PV+
TP1
1
BUCK_IN+
TP2
1
+5V
TP3
1
MID
TP4
1
+3V3
TP5
1
GND
TP6
1
VDIV
TP7
1
ISENSE
TP8
1
GATE
TP9
1
RTC_INT
TP10
1
RTC_32K
TP11
1
Green, ~0.3 mA
LED1
1
>=100 V >=15 A dual Schottky (e.g. 20 A 100 V)
D0
1
S3M (1000 V 3 A)
D1
1
SMAJ5.0A (TVS, unidirectional)
D2
1
ESD 3.3 V (e.g. PESD3V3L1BA)
D3
1
SS14 (flyback clamp)
D4
1
Schottky >=100 V >=10 A (MBR10100 class)
D5
1
DNP: SMCJ58A TVS (fit after bench test if needed)
D6
1
470u 10 V low ESR
C3
5
100n
C4, C5, C6, C9, C10
1
10n
C7
1
10u
C8
3
1u
C11, C12, C13
1
100k 1%
R1
1
4k7 1%
R2
1
10R
R4
6
10k
R5, R9, R14, R15, R16, R17
1
1k
R6
2
10k
R7, R8
3
4k7
R10, R11, R12
1
100R
R13
2
100k
R18, R21
1
0R
R19
1
DNP
R20

SUNDIAL design files

The KiCad project lives in the photovoltaic-art/SUNDIAL repository on GitHub; these links point at the commit this page was built from.

SUNDIAL: common questions

What microcontroller does the SUNDIAL use?

The SUNDIAL is built around the PinSocket_1x15_P2.54mm_Vertical, from the ESP32 family.

How many components are on the SUNDIAL?

82 components, from 64 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the SUNDIAL design files?

From the photovoltaic-art/SUNDIAL repository on GitHub, which has the schematic, a netlist and the BOM; the links under Design files point to each one.

Can I use the SUNDIAL design in my own project?

The repository has no license, so all rights stay with photovoltaic-art. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the SUNDIAL without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards