Megabot-KeychainV1
planetisrocky·Megabot-KeychainV1
About the Megabot-KeychainV1 PCB
Megabot-KeychainV1 is an open source ESP32 PCB design by planetisrocky, published on GitHub. It is a 2-layer board measuring 47 × 47 mm, with 4 components from 4 distinct parts.
Its main chip is the ESP32C3, from the ESP32 family. By type, the board carries 3 connectors and 1 IC.
It belongs with the audio, power & battery and iot & wireless designs in this gallery.
From the project
A tiny digital & interactive keychain, depicting none other than Megabot from Big Hero 6! I'll add a time feature to show the current time with a button click, and hopefully more is on Made for Week #1 of Hack Club's Half Life program ❤️
A Big Hero 6 inspired figure with a round display for a face. It shows emotions, the time, weather, and more, and you switch modes with buttons. Built for Hack Club's Half Life program.
- 1.28" round display (GC9A01, 240x240) as the face - Emotions switched with one of 3 buttons - Time calibrated over WiFi (NTP) - Weather and more modes to come - I2S header for a MAX98357A amp and speaker (voice lines and UI sounds) - Rechargeable single-cell LiPo, charged over USB-C through the XIAO

Main components on the Megabot-KeychainV1
Megabot-KeychainV1 bill of materials (BOM)
4 components, 4 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32C3 | MODULE_XIAO_ESP32C3 | U1 |
| 1 | AUDIO | PinHeader_1x05_P2.54mm_Vertical | J1 |
| 1 | SCREEN | PinHeader_1x07_P2.54mm_Vertical | J2 |
| 1 | BUTTONS | PinHeader_1x04_P2.54mm_Vertical | J3 |
Megabot-KeychainV1 design files
The KiCad project lives in the planetisrocky/Megabot-KeychainV1 repository on GitHub; these links point at the commit this page was built from.
- LayoutMegabotPCB.kicad_pcb
- SchematicMegabotPCB.kicad_sch
Megabot-KeychainV1: common questions
What microcontroller does the Megabot-KeychainV1 use?
The Megabot-KeychainV1 is built around the ESP32C3, from the ESP32 family.
How big is the Megabot-KeychainV1 PCB?
The Megabot-KeychainV1 measures 47 × 47 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Megabot-KeychainV1?
4 components, from 4 distinct parts. The full bill of materials is listed on this page.
Where can I download the Megabot-KeychainV1 design files?
From the planetisrocky/Megabot-KeychainV1 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Megabot-KeychainV1 design in my own project?
The repository has no license, so all rights stay with planetisrocky. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Megabot-KeychainV1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k