PumaTX DB HW00
About the PumaTX DB HW00 PCB
PumaTX DB HW00 is an open source PCB design by PumaFPV, published on GitHub under the MIT license. It is a 2-layer board measuring 121.3 × 42.6 mm, with 32 components from 9 distinct parts.
By type, the board carries 12 capacitors, 11 resistors, 6 switches, 2 connectors and 1 diode.
It belongs with the power & battery designs in this gallery.
From the project
DIY FPV Remote controller based on the one from the mavic
RC04: Software: PPM SBus Hall Effect Pots reading (Left pot mode switch left = down ; Right = up ; RTH = overwrite) Arm reading Pre reading RTH reading Power on / off via sport switch basic screen use + vbat + splash screen
Hardware: Micro USB (from controller) 2S LiPo external RF (R9M) USB 2.0 (or 3.0 if I find one,) to plug in module (gnd, 5v, VBat, Tx) Support for JR module in phone holder
PumaTX DB HW00 bill of materials (BOM)
32 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USB_B_Micro | USB_Micro-B_Molex-105133-0001 | J1 |
| 1 | FH12A-26S-0.5SH(55) FH12A-26S-0.5SH_55_ | FH12A26S05SH55 | J2 |
| 5 | SKRPABE010 | SKRPABE010 | S1, S2, S3, S5, S6 |
| 1 | SKRHABE010 | SKRHABE010 | S4 |
| 1 | LED | C_0402_1005Metric | D1 |
| 12 | C | C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C7, C8 +4 |
| 9 | R | C_0402_1005Metric | R1, R2, R3, R4, R5, R6, R7, R8 +1 |
| 1 | 1k1 | C_0402_1005Metric | R10 |
| 1 | 11 | C_0402_1005Metric | R11 |
PumaTX DB HW00 design files
The KiCad project lives in the PumaFPV/PumaTX repository on GitHub; these links point at the commit this page was built from.
PumaTX DB HW00: common questions
How big is the PumaTX DB HW00 PCB?
The PumaTX DB HW00 measures 121.3 × 42.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PumaTX DB HW00?
32 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the PumaTX DB HW00 design files?
From the PumaFPV/PumaTX repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the PumaTX DB HW00 design in my own project?
Yes, under the terms of its MIT license, which PumaFPV chose for the repository.
More boards in PumaTX
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0k
Stack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7k
Display Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7k
Module 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k
TemperaturePCB PANEL
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1k
ProgrammingAdapter
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1k