Yatagarsu
QUT-EESS·OmniBot·Electronics/System Controller/SystemController.kicad_pcb
About the Yatagarsu PCB
Yatagarsu is an open source STM32 PCB design by QUT-EESS, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 55.1 × 45.7 mm, with 60 components from 30 distinct parts.
Its main chip is the STM32F103CBT6, from the STM32 family. Other key parts include the LM317 and Seeedstudio_Buck_5v. By type, the board carries 20 resistors, 15 capacitors, 9 diodes, 6 connectors, 2 ICs and 2 transistors.
It belongs with the robotics & motion designs in this gallery.
From the project
EESS Modular Robotics Platform
An open source modular robotics platform designed with KiCAD and FreeCAD. Custom designed Chassis designed to be laser cut/3d printed/CnC Milled. Custom fit stepper motor mounts with embedded motor controller PCB.
Main Processor unit consists of a Raspberry Pi A+ for path planning and general computation. An STM32 ARM microcontroller system controller will handle the stepper motor control via communication with the RPi A+ board and motor controllers.

Main components on the Yatagarsu
Yatagarsu bill of materials (BOM)
60 components, 30 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM317 | SOT-223 | U1 |
| 1 | Seeedstudio_Buck_5v | Seeedstudio_5V_Buck | U2 |
| 1 | 2N7002 | SOT-23 | Q1 |
| 1 | Si2343CDS | SOT-23 | Q2 |
| 1 | 8MHz | HC49SDLF_Crystal_Series | Y1 |
| 1 | 32kHz | QTC3_Series_Crystal | Y2 |
| 1 | Battery Input | Molex_MicroFit_3.0_RightAngle | P1 |
| 1 | SWD | Tag-Connect_6P_Leads | P2 |
| 1 | Raspberry Pi A+ Connectors | Raspberry_Pi_A+ | P3 |
| 3 | Harwin-10P | Pin_Header_Straight_2x05 | P4, P5, P6 |
| 1 | BOOT0 | Pin_Header_Straight_1x03 | JP1 |
| 1 | BOOT1 | Pin_Header_Straight_1x03 | JP2 |
| 1 | SW_PUSH | B3F-1025_Tactile_Switch | SW1 |
| 1 | STM32F103CBT6 | LQFP-48_7x7mm_Pitch0.5mm | uC1 |
| 9 | LED | LED_0805 | D1, D2, D3, D4, D5, D6, D7, D8 +1 |
| 6 | 100nF | C_0805 | C1, C3, C4, C7, C11, C15 |
| 2 | 22pF | C_0805 | C2, C5 |
| 3 | 1uF | C_0805 | C6, C12, C13 |
| 1 | 10uF | C_0805 | C8 |
| 2 | 4.7pF | C_0603 | C9, C14 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1nF | C_0805 | C10 |
| 4 | 10K | R_0805_HandSoldering | R1, R2, R5, R6 |
| 1 | 910 | R_0805_HandSoldering | R3 |
| 1 | 390 | R_0805_HandSoldering | R4 |
| 1 | 240 | R_0805_HandSoldering | R7 |
| 6 | 68 | R_0603_HandSoldering | R8, R13, R14, R15, R16, R18 |
| 2 | 560 | R_0603_HandSoldering | R9, R17 |
| 2 | R | R_0603_HandSoldering | R10, R11 |
| 1 | 150 | R_0603_HandSoldering | R12 |
| 2 | R_I2C | R_0805_HandSoldering | R19, R20 |
Yatagarsu design files
The KiCad project lives in the QUT-EESS/OmniBot repository on GitHub; these links point at the commit this page was built from.
Yatagarsu: common questions
What microcontroller does the Yatagarsu use?
The Yatagarsu is built around the STM32F103CBT6, from the STM32 family.
How big is the Yatagarsu PCB?
The Yatagarsu measures 55.1 × 45.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Yatagarsu?
60 components, from 30 distinct parts. The full bill of materials is listed on this page.
Where can I download the Yatagarsu design files?
From the QUT-EESS/OmniBot repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Yatagarsu design in my own project?
Yes, under the terms of its GPL-3.0 license, which QUT-EESS chose for the repository.
Can I test firmware for the Yatagarsu without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in OmniBot
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k