47 open source boards using the LM317
Real designs built with the LM317, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
C6021light
GBert
100 × 50 mm74 parts2LNo license36Alim10o
acmo0
137.8 × 91.4 mm86 parts2LGPL-3.014DualLM317BenchSupply
cellularmitosis
99.1 × 99.7 mm49 parts2LMIT12AVR/Arduino
NoahFC
zosko
32 × 42 mm41 parts2LGPL-3.012Audioswitch
zehome
120 × 50 mm80 parts2LBSD-3-Clause1074Logic SA ADC
schilkp
95.9 × 69.2 mm189 parts2LMIT9AVR/Arduino
Rvi v2x hardware
PDXostc
85 × 56 mm186 parts2LMPL-2.09AVR/Arduino
Iz1glg yaacw keyer
federicobriata
110 × 92.7 mm78 parts2LCC-BY-SA-4.07AVR/Arduino
Led wordclock
Virtex7
80 × 50.8 mm74 partsNo license4FPGA
Xc17 prom prog
msinger
123 × 95 mm281 parts2LCC-BY-SA-4.03PSU-5V-6V-Dual9V
ohdsp
100 × 100 mm103 parts2LTAPR-OHL-1.03Arithmetic
bodokaiser
49.5 × 48.8 mm59 parts2LNo license3Master segnale
dj-filippo241
100 × 220 mm275 parts4LNo license2ZFireAlarm
its-villada
100 × 50 mm44 parts2LGPL-3.02AVR/Arduino
OutFox
ShaunPrice
96.5 × 96.5 mm88 parts2LApache-2.01AVR/Arduino
Ulang sys res
lonapse456-glitch
84.2 × 86.4 mm41 parts2LNo license1Audio preamplifier power supply
flavian112
106.7 × 43.2 mm32 parts2LNo license1AVR/Arduino
Console-Server
TheKingOfChaos
138 × 141 mm284 parts4LNo license0Cuk iso ps
mtguerreiro
225 × 130 mm151 parts2LBSD-3-Clause0STM32
SYS StepAtten
schilkp
122 × 84 mm142 parts2LMIT0STM32
Yatagarsu
QUT-EESS
55.1 × 45.7 mm60 parts2LGPL-3.00ESP32
TSI SmartVent KiCAD May2026
ishron256
95 × 54.4 mm45 parts4LNo license0AVR/Arduino
Arduino-Wi-Fi-Signal-Strength-Tool
rajsinghtech
123.1 × 54.4 mm28 parts4LNo license0Fonte introee final
phckopper
67.3 × 67.3 mm25 parts2LNo license0AVR/Arduino
MostekDumper
chregu82
100 × 57 mm21 parts2LNo license0OpenPAT-RP2040
lukasnf
65.5 × 45 mm21 parts2LMIT0The zapfish variable supply
ItsKareem
34 × 34 mm8 parts2LNo license0- schematic only · 697 parts
Master
plektra
697 parts2LCustom license0 - schematic only · 36 partsAVR/Arduino
Breadboard-Power-Supply
leboeuf-dup
36 parts2LNo license0 - schematic only · 331 parts
Channel card
plektra
331 parts2LCustom license0 S88iso
GBert
70 × 50 mm29 parts2LNo license36Main board
Windfisch
98 × 54.4 mm76 parts2LGPL-3.031AVR/Arduino
Wp controller
pypilot
75.1 × 50 mm77 parts4LNo license3Mic
dj-filippo241
100 × 220 mm204 parts4LNo license2Pwm tl494cn
jonronen
63.5 × 45.5 mm39 parts2LNo license1C8051-test
GBert
48.3 × 54.6 mm13 parts2LNo license36
How designs wire the LM317
Read from the KiCad layouts of 33 open source designs, one per repository: what each pin of the LM317 connects to, and the resistors, capacitors and other passives placed on it.
- The ADJ pin has a resistor to GND on 18 of 32 designs, most often 2.2 kΩ (then 750 Ω).
- The VI pin has a decoupling capacitor on 18 of 32 designs, most often 100 nF (then 2.2 mF).
- The ADJ pin has a pull-up to 3.3V on 17 of 32 designs, most often 240 Ω (then 330 Ω).
- The ADJ pin has a series resistor on 15 of 32 designs, most often 10 Ω (then 220 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADJpin 1 | Connected to: Signal 97% |
|
| VOpin 2 | Connected to: 3.3V 53% · a signal 44% |
|
| VIpin 3 | Connected to: 12V 63% · a signal 38% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Smallest Rocrail Server Ever II by GBert, C6021light by GBert, Main board by Windfisch and Alim10o by acmo0.
The LM317 in open source designs
The gallery holds 47 open source boards using the LM317 from 35 GitHub repositories; a typical one measures about 98.5 × 56.5 mm and carries around 76 components.
70% are two-layer designs, the rest use four layers or more, and 34% carry an open source license.
The most starred is Smallest Rocrail Server Ever II by GBert.
Microcontrollers on boards using the LM317
What boards using the LM317 are built for
LM317: common questions
Where can I find a LM317 reference design?
Each of the 47 boards on this page is a real design using the LM317. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM317 ADJ pin?
The ADJ pin has a resistor to GND on 18 of 32 designs, most often 2.2 kΩ (then 750 Ω). Counted from the KiCad layouts of 33 open source designs using the LM317.
What decoupling capacitors do designs use on the LM317 VI pin?
The VI pin has a decoupling capacitor on 18 of 32 designs, most often 100 nF (then 2.2 mF). Counted from the KiCad layouts of 33 open source designs using the LM317.
What parts are used alongside the LM317?
The LM337, LM339, LM358 and LM7805 appear in the most repositories here.
Which microcontrollers do boards using the LM317 use?
Most are built on AVR/Arduino (13), STM32 (2), ESP32 (1) and FPGA (1).
How big is a typical board using the LM317?
The median is 98.5 × 56.5 mm, and 70% are two-layer designs.
What is the most popular open source board using the LM317?
By GitHub stars, Smallest Rocrail Server Ever II by GBert, with 99 stars.
Can I simulate one of these boards using the LM317 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.