Van gogh
Rhiiino·van-gogh·kicad/barrel-logicBoard-vanGogh.kicad_pcb
About the Van gogh PCB
Van gogh is an open source ESP32 PCB design by Rhiiino, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 56 × 92.6 mm, with 29 components from 20 distinct parts.
Its main chip is the ESP32_s3_supermini, from the ESP32 family. Other key parts include the D36V50F6. By type, the board carries 9 capacitors, 7 resistors, 6 connectors, 4 ICs, 2 transistors and 1 diode.
From the project
First barrel variant for the Panzer project
Right-barrel barrel control unit (BCU) PCB. Open barrel-logicBoard-vanGogh.kicadpro` in KiCad.
gerber.zip is the Gerber and drill export for PCB fab. It matches the board ordered from JLCPCB as Y14-2705430A. Upload the zip as-is; no KiCad required to order bare boards.
- board.md — every reference and pin - bom.md — parts to solder on the board
Main components on the Van gogh
Van gogh bill of materials (BOM)
29 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | MP1584 | U1 |
| 1 | D36V50F6 | D36V50F6 | U2 |
| 1 | ~ | ESP32_s3_supermini | U3 |
| 1 | ~ | DRV8833 | U4 |
| 2 | Q_NMOS_GDS | TO-252-2 | Q1, Q2 |
| 1 | 6-pin molex inlet | SolderWire-0.5sqmm_1x06_P4.6mm_D0.9mm_OD2.1mm | J1 |
| 1 | DIAL N20 | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | Cone N20 | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J3 |
| 1 | LED stick | JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J4 |
| 1 | Laser | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J5 |
| 1 | Solenoid | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J6 |
| 1 | D_Schottky | D_SMA_Handsoldering | D1 |
| 1 | 100uF | CP_Radial_D8.0mm_P3.50mm | C1 |
| 4 | 100nF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2, C3, C8, C9 |
| 2 | 100µF | CP_Radial_D6.3mm_P2.50mm | C4, C6 |
| 2 | 10µF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C5, C7 |
| 3 | 100Ω | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R2, R4 |
| 1 | 330Ω | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3 |
| 2 | 10k Ω | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R5, R7 |
| 1 | 100 Ω | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6 |
Van gogh design files
The KiCad project lives in the Rhiiino/van-gogh repository on GitHub; these links point at the commit this page was built from.
Van gogh: common questions
What microcontroller does the Van gogh use?
The Van gogh is built around the ESP32_s3_supermini, from the ESP32 family.
How big is the Van gogh PCB?
The Van gogh measures 56 × 92.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Van gogh?
29 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the Van gogh design files?
From the Rhiiino/van-gogh repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Van gogh design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Van gogh without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k