Stepper control
Roboy·VRpuppet·hardware/stepper_control/stepper_control.kicad_pcb
About the Stepper control PCB
Stepper control is an open source AVR/Arduino PCB design by Roboy, published on GitHub under the BSD-3-Clause license. It is a 2-layer board measuring 156 × 86 mm, with 20 components from 13 distinct parts.
Its main chip is the Arduino_Mega2560_Shield, from the AVR/Arduino family. Other key parts include the Pololu_Breakout_A4988. By type, the board carries 13 connectors and 6 modules.
It belongs with the robotics & motion designs in this gallery.
From the project
An actor struggles to die onstage, but a puppet has to struggle to live
Main components on the Stepper control
Stepper control bill of materials (BOM)
20 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 6 | Pololu_Breakout_A4988 | Pololu_Breakout-16_15.2x20.3mm | A1, A2, A3, A4, A5, A6 |
| 1 | POWER | Wago_2060_2_SMD | J1 |
| 1 | motor0 | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | motor1 | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | motor2 | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | motor3 | PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | motor4 | PinHeader_1x04_P2.54mm_Vertical | J6 |
| 2 | Conn_01x02_Male | PinHeader_1x02_P2.54mm_Vertical | J7, J12 |
| 1 | motor5 | PinHeader_1x04_P2.54mm_Vertical | J8 |
| 2 | Conn_01x09_Male | PinHeader_1x09_P2.54mm_Vertical | J9, J10 |
| 1 | Conn_01x01_Male | PinHeader_1x01_P2.54mm_Vertical | J11 |
| 1 | SPI | PinHeader_1x05_P2.54mm_Vertical | J13 |
| 1 | Arduino_Mega2560_Shield | Arduino_Mega2560_Shield | XA1 |
Stepper control design files
The KiCad project lives in the Roboy/VRpuppet repository on GitHub; these links point at the commit this page was built from.
Stepper control: common questions
What microcontroller does the Stepper control use?
The Stepper control is built around the Arduino_Mega2560_Shield, from the AVR/Arduino family.
How big is the Stepper control PCB?
The Stepper control measures 156 × 86 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Stepper control?
20 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Stepper control design files?
From the Roboy/VRpuppet repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Stepper control design in my own project?
Yes, under the terms of its BSD-3-Clause license, which Roboy chose for the repository.
Can I test firmware for the Stepper control without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in VRpuppet
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k