STM32-GPS-CubeSat
rohanasgowda·STM32-GPS-CubeSat·Hardware/PCB/STM32_GPS_CubeSat.kicad_pcb
About the STM32-GPS-CubeSat PCB
STM32-GPS-CubeSat is an open source STM32 PCB design by rohanasgowda, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 35.5 × 31.3 mm, with 19 components from 12 distinct parts.
Its main chip is the STM32F407VGTX, from the STM32 family. By type, the board carries 9 capacitors, 6 connectors, 2 resistors, 1 IC and 1 switch.
It belongs with the rf & radio, science & space and displays & leds designs in this gallery.
From the project
Custom STM32-based PCB design featuring GPS interfacing and peripheral connectivity, designed using KiCad.
Custom STM32-based PCB design featuring GPS-related signal connections and peripheral connectivity, designed using KiCad. This repository contains the KiCad source files, generated manufacturing outputs, bill of materials, design reports, and board visualizations.
The design is centered on an STM32F407VGTx microcontroller. The schematic and board provide labeled connections for GPS- and radio-related signals, microSD, an OLED display, debugging, and power input. The repository documents the PCB design; it does not establish that the board has been assembled, programmed, or functionally…

Main components on the STM32-GPS-CubeSat
STM32-GPS-CubeSat bill of materials (BOM)
19 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F407VGTX STM32F407VGTx | LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | SWD_DEBUG | PinHeader_1x05_P2.54mm_Vertical | J1 |
| 1 | CONN_01X05 GPS | PinHeader_1x05_P2.54mm_Vertical | J2 |
| 1 | MICROSD_SPI | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | OLED_I2C | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | CONN_01X04 Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | EPS_POWER_INPUT | PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 6 | 100NF 100nF | C_0805_2012Metric | C1, C2, C3, C4, C5, C6 |
| 1 | 4.7UF 4.7uF | C_0805_2012Metric | C7 |
| 2 | 2.2UF 2.2uF | C_0805_2012Metric | C8, C9 |
| 2 | 10K 10k | R_0805_2012Metric | R1, R2 |
STM32-GPS-CubeSat design files
The KiCad project lives in the rohanasgowda/STM32-GPS-CubeSat repository on GitHub; these links point at the commit this page was built from.
STM32-GPS-CubeSat: common questions
What microcontroller does the STM32-GPS-CubeSat use?
The STM32-GPS-CubeSat is built around the STM32F407VGTX, from the STM32 family.
How big is the STM32-GPS-CubeSat PCB?
The STM32-GPS-CubeSat measures 35.5 × 31.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the STM32-GPS-CubeSat?
19 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the STM32-GPS-CubeSat design files?
From the rohanasgowda/STM32-GPS-CubeSat repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the STM32-GPS-CubeSat design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which rohanasgowda chose for the repository.
Can I test firmware for the STM32-GPS-CubeSat without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k