Main
Sanassah·RocketPower·PCB/main/main.kicad_pcb
About the Main PCB
Main is an open source NXP PCB design by Sanassah, published on GitHub under the MIT license. It is a 4-layer board measuring 53.7 × 53.7 mm, with 113 components from 64 distinct parts.
Its main chip is the MIMXRT1062DVL6B, from the NXP family. Other key parts include the GPS. By type, the board carries 39 capacitors, 32 resistors, 6 diodes, 4 crystals, 4 inductors and 3 transistors.
From the project
Active fin control flight computer for a model rocket, built from scratch: custom PCB, Cortex-M7 firmware, PD attitude control, and hardware-in-the-loop testing.
Main components on the Main
Main bill of materials (BOM)
113 components, 64 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | GPS | UBLOX_ZOE_M8-0-10 | U-BLOX_ZOE_M8Q-0-1 |
| 3 | SI2302 DMG3406L | SOT-23 | Q1, Q2, Q3 |
| 2 | 32.768KHZ 32.768kHz | Crystal_SMD_2012-2Pin_2.0x1.2mm_HandSoldering | Y1, Y3 |
| 1 | 32.768KHZ 32.768kHz | 830050789 | Y4 |
| 1 | XRCGB24M000F2P29R0 | XRCGB | Y5 |
| 1 | 584-ADXL375BCCZ ACC | ADXL375BCCZRL | ADXL1 |
| 1 | 262-BMP390 ALTIMETER | BMP388 | BMP1 |
| 1 | 526-BNO085 IMU | BNO085 | BNO1 |
| 1 | CONMHF1-SMD-G-T ANTENNA | CONMHF1SMDGT | CONMHF1-SMD-G-T1 |
| 1 | DM3D-SF MicroSD | DM3DSF | DM3D-SF1 |
| 1 | 530-C1F6 6A | Fuse_1206_3216Metric | F1 |
| 1 | GD25Q64ESIG | GD25Q64ESIG | FLASH1 |
| 1 | INA260 | TSSOP16 | INA1 |
| 1 | S4B-PH-K-S(LF)(SN) TELEMETRY | JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_Vertical | JST-GH-1 |
| 1 | S4B-PH-K-S(LF)(SN) CAMERA | JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_Vertical | JST-GH-2 |
| 1 | KMR241GLFS RESET | KMR421GULCLFS | KMR241GLFS1 |
| 1 | MIMXRT1062DVL6B MCU | BGA196C80P14X14_1200X1200X152 | MIMXRT1062DVL6B1 |
| 1 | MKL02Z32VFG4 BOOT | QFN50P300X300X65-17N-D | MKL02Z32VFG1 |
| 1 | SERVO1 | JST_GH_BM03B-GHS-TBT_1x03-1MP_P1.25mm_Vertical | SERVO1 |
| 1 | SERVO2 | JST_GH_BM03B-GHS-TBT_1x03-1MP_P1.25mm_Vertical | SERVO2 |
Show 44 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SERVO3 JST | JST_GH_BM03B-GHS-TBT_1x03-1MP_P1.25mm_Vertical | SERVO3 |
| 1 | SERVO4 | JST_GH_BM03B-GHS-TBT_1x03-1MP_P1.25mm_Vertical | SERVO4 |
| 1 | 1725711 | 1725711 | ScrewTerminal1 |
| 1 | 651-1725656 BATT | 1725656 | ScrewTerminal2 |
| 3 | TESTPOINT_2POLE TestPoint_2Pole | TestPoint_2Pads_Pitch2.54mm_Drill0.8mm | TP1, TP2, TP3 |
| 1 | TPS62111RSAR 3.3Vreg | TPS62111RSAR | TPS62111RSAR1 |
| 1 | USBc | USB_C_Receptacle_GCT_USB4110 | USB_C_Receptacle_USB2.0_14P1 |
| 1 | 78-TLMG1100-GS15 3.3V LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | 78-TLMG1100-GS15 BOOT LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | 78-TLMG1100-GS15 GPS LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3 |
| 1 | 78-TLMG1100-GS15 Altimeter LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D4 |
| 1 | 78-TLMG1100-GS15 200G ACC LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D5 |
| 1 | 78-TLMG1100-GS15 IMU LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D6 |
| 2 | 120 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | FB1, FB2 |
| 1 | 6.8UH 6.8uH | L_1008_2520Metric_Pad1.43x2.20mm_HandSolder | L1 |
| 1 | 4.7UH 4.7uH | L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L2 |
| 3 | 10UF 10uF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C1, C11, C28 |
| 1 | 22UF 22uF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C2 |
| 2 | 1UF 1uF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C3, C36 |
| 9 | 0.22UF 0.22uF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C5, C12, C13, C18, C19, C20, C21, C22 +1 |
| 1 | 2.2UF 2.2uF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C6 |
| 1 | 10NF 10uF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C7 |
| 5 | 4.7UF 4.7uF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C8, C14, C15, C16, C27 |
| 2 | 18PF 18pF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C9, C10 |
| 1 | 0.22UF 10nF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C17 |
| 2 | 10PF 10pF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C23, C24 |
| 1 | 10NF 10nF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C25 |
| 7 | 0.1UF 0.1uF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C29, C30, C31, C34, C35, C37, C39 |
| 2 | 22PF 22pF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C32, C33 |
| 1 | 1UF 0.1uF | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | C40 |
| 1 | 470UF 470uf | C_Radial_D6.3mm_H11.0mm_P2.50mm | C41 |
| 2 | 5.1K 5.1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 1 | 1M | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 470 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 5 | 470 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R7, R9, R11, R12 |
| 5 | 4.7K 4.7k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R8, R14, R15, R16 |
| 1 | 2.2M | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 1 | 100K 100k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13 |
| 5 | 10K 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R17, R19, R20, R24, R28 |
| 1 | 10K 4.7k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R18 |
| 3 | 7 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R21, R25, R29 |
| 3 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R22, R26, R30 |
| 3 | 10K 7.32k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R23, R27, R31 |
| 1 | 4.7k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R32 |
Main design files
The KiCad project lives in the Sanassah/RocketPower repository on GitHub; these links point at the commit this page was built from.
Main: common questions
What microcontroller does the Main use?
The Main is built around the MIMXRT1062DVL6B, from the NXP family.
How big is the Main PCB?
The Main measures 53.7 × 53.7 mm, has 4 copper layers and is 1.635 mm thick.
How many components are on the Main?
113 components, from 64 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Main design files?
From the Sanassah/RocketPower repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Main design in my own project?
Yes, under the terms of its MIT license, which Sanassah chose for the repository.
Can I test firmware for the Main without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
More boards in RocketPower
Similar boards
NXP
32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763NXP
Mega-Cube-Board
MaltWhiskey
200 × 54 mm100 parts4LNo license763NXP
MCL6809
MicroCoreLabs
32.3 × 61 mm7 parts4LNo license532NXP
MCL68
MicroCoreLabs
31.6 × 84.1 mm13 parts4LNo license532NXP
MCL65+
MicroCoreLabs
72.6 × 64.1 mm6 parts2LNo license532NXP
MCLZ8
MicroCoreLabs
37.1 × 61.5 mm6 parts4LNo license532