8 open source boards using the GPS

Real designs built with the GPS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the GPS

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the GPS connects to, and the resistors, capacitors and other passives placed on it.

  • The NRESET pin is left unconnected on 4 of 6 designs.
  • The VCC_RF pin is left unconnected on 3 of 4 designs.
  • The RESERVADO pins is left unconnected on 63% of them (GND on 2).
  • The TXD1 pins have a capacitor to GND on 2 of 4 designs, most often 100 nF.
GNDpin 1, 10, 12Connected to: GND 65% · not connected 23%
VBATpin 6Connected to: Not connected 33% · 3.3V 33% · a signal 33%
  • Decoupling capacitor on 33% · 10 µF (2)
NCpin 7, 13Connected to: Not connected 60% · GND 40%
VCCpin 8Connected to: 3.3V 67% · GND 17% · a signal 17%
  • Decoupling capacitor on 33% · 10 µF (2)
NRESETpin 9Connected to: Not connected 67% · GND 17% · 3.3V 17%
VCC_RFpin 14Connected to: Not connected 75% · GND 25%
RESERVADOpin 15, 18Connected to: Not connected 63% · GND 25%
TXD1pin 17, 25Connected to: Not connected 33% · GND 17% · 3.3V 17% · a signal 33%
  • Capacitor to GND on 50% · 100 nF (1)

6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Minino by ElectronicCats, Horizon by Horizon-Avionics, Safecast air teensy by Safecast and Main by Sanassah.

The GPS in open source designs

The gallery holds 8 open source boards using the GPS from 7 GitHub repositories; a typical one measures about 80 × 107.5 mm and carries around 53 components.

75% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.

The most starred is Minino by ElectronicCats.

Microcontrollers on boards using the GPS

GPS: common questions

Where can I find a GPS reference design?

Each of the 8 boards on this page is a real design using the GPS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the GPS NRESET pin connected?

The NRESET pin is left unconnected on 4 of 6 designs. Counted from the KiCad layouts of 7 open source designs using the GPS.

How is the GPS VCC_RF pin connected?

The VCC_RF pin is left unconnected on 3 of 4 designs. Counted from the KiCad layouts of 7 open source designs using the GPS.

How is the GPS RESERVADO pin connected?

The RESERVADO pins is left unconnected on 63% of them (GND on 2). Counted from the KiCad layouts of 7 open source designs using the GPS.

What parts are used alongside the GPS?

The ESP32-C6-WROOM-1U-N8, LNA and XC6220B331MR-G appear in the most repositories here.

Which microcontrollers do boards using the GPS use?

Most are built on ESP32 (3) and NXP (3).

How big is a typical board using the GPS?

The median is 80 × 107.5 mm, and 75% are two-layer designs.

What is the most popular open source board using the GPS?

By GitHub stars, Minino by ElectronicCats, with 178 stars.

Can I simulate one of these boards using the GPS before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part