Board a main
sashankthapa·fingertip-fusion-hw·hardware/board-a-main/board-a-main.kicad_pcb
About the Board a main
Board a main is an open source STM32 PCB design by sashankthapa, published on GitHub. It is a 2-layer board measuring 40 × 25 mm, with 23 components from 14 distinct parts.
Its main chip is the STM32F446RETx, from the STM32 family. Other key parts include the USBLC6-2SC6 and AP2112K-3.3. By type, the board carries 9 capacitors, 5 resistors, 3 ICs, 3 connectors and 1 LED.
It belongs with the sensors designs in this gallery.
From the project
This project implements a two-board hardware architecture for acquiring data from an IMU. The system consists of:
This project implements a two-board hardware architecture for acquiring data from an IMU. The system consists of:
- Board A: Main controller (STM32F446R) board responsible for USB communication, power regulation, timestamping, and interfacing with the host PC. - Board B: ICM-42688-P sensor board carrying an SPI IMU. The architecture separates the processing electronics from the sensing electronics, allowing the sensor to be placed on a fingertip. dimensions are (18mm x 14mm)
Main components on the Board a main
Board a main bill of materials (BOM)
23 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2SC6 | SOT-23-6 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | STM32F446RETx | LQFP-64_10x10mm_P0.5mm | U3 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | Conn_01x08 | JST_GH_BM08B-GHS-TBT_1x08-1MP_P1.25mm_Vertical | J2 |
| 1 | Conn_01x04 | PinHeader_1x04_P1.00mm_Vertical | J3 |
| 2 | SW_Push | SW_SPST_EVQP2_MiddlePushTravel_H2.5mm | BOOT1, RESET1 |
| 1 | LED | LED_0805_2012Metric | STATUS1 |
| 5 | 100nf | C_0201_0603Metric | C1, C5, C6, C7, C8 |
| 3 | 10uf | C_0201_0603Metric | C2, C3, C4 |
| 1 | 4.7uf | C_0201_0603Metric | C9 |
| 2 | 5.1k | R_0201_0603Metric | R1, R2 |
| 2 | 10k | R_0201_0603Metric | R3, R4 |
| 1 | 330 | R_0201_0603Metric | R5 |
Board a main design files
The KiCad project lives in the sashankthapa/fingertip-fusion-hw repository on GitHub; these links point at the commit this page was built from.
Board a main: common questions
What microcontroller does the Board a main use?
The Board a main is built around the STM32F446RETx, from the STM32 family.
How big is the Board a main?
The Board a main measures 40 × 25 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Board a main?
23 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Board a main design files?
From the sashankthapa/fingertip-fusion-hw repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Board a main design in my own project?
The repository has no license, so all rights stay with sashankthapa. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Board a main without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in fingertip-fusion-hw
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k