PedalCtrl
schilkp·PedalCtrl·ECAD/PedalCtrl/PedalCtrl.kicad_pcb
About the PedalCtrl PCB
PedalCtrl is an open source PIC PCB design by schilkp, published on GitHub under the MIT license. It is a 2-layer board measuring 73.7 × 45.7 mm, with 22 components from 18 distinct parts.
Its main chip is the PIC12F1572, from the PIC family. Other key parts include the L7805. By type, the board carries 8 connectors, 4 resistors, 3 diodes, 3 capacitors, 2 ICs and 1 transistor.
It belongs with the audio designs in this gallery.
From the project
A very simple, PIC12F1572-based, footpedal-controlled, relay 250V Mains switch.
A very simple, PIC12F1572-based, footpedal-controlled, relay 250V Mains switch.
Please don't work with mains-connected circuits unless you know what you are doing.
Waiting for PCB prototype to develop Firmware.
Allows mains-powered devices to be quickly powered on and off using a footswitch. Both Line and Neutral are switched.
Pressing the pedal once enables the device and starts an automatic timer controlled by the potentiometer. Once that timer runs out, or the pedal is pressed again, the device will switch back off.

Main components on the PedalCtrl
PedalCtrl bill of materials (BOM)
22 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | L7805 | TO-252-2 | U1 |
| 1 | PIC12F1572 | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | STD5NK50ZT4 | TO-252-2 | Q2 |
| 1 | V_in | TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J1 |
| 1 | AC IN | TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J2 |
| 1 | POTI | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | LED | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | ICSP | PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | PEDAL | PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | AC OUT | TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J7 |
| 1 | Power Supply | TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J8 |
| 1 | FINDER-40.62 | Relay_DPDT_Finder_40.52 | K1 |
| 2 | 5V5 | D_SOD-123 | D2, D3 |
| 1 | 1N4001 | D_SOD-123F | D4 |
| 1 | 10u | CP_Elec_6.3x7.7 | C1 |
| 2 | 0u1 | C_0603_1608Metric | C2, C3 |
| 1 | 1K | R_0603_1608Metric | R2 |
| 3 | 10K | R_0603_1608Metric | R3, R4, R5 |
PedalCtrl design files
The KiCad project lives in the schilkp/PedalCtrl repository on GitHub; these links point at the commit this page was built from.
PedalCtrl: common questions
What microcontroller does the PedalCtrl use?
The PedalCtrl is built around the PIC12F1572, from the PIC family.
How big is the PedalCtrl PCB?
The PedalCtrl measures 73.7 × 45.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PedalCtrl?
22 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the PedalCtrl design files?
From the schilkp/PedalCtrl repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the PedalCtrl design in my own project?
Yes, under the terms of its MIT license, which schilkp chose for the repository.
Can I test firmware for the PedalCtrl without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
Similar boards
PIC
Pslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7kPIC
Lens
ervanalb
80 × 80 mm53 parts4LNo license515PIC
Micro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414PIC
GB-CARTPP-DIY
Gekkio
100 × 100 mm22 parts2LCC-BY-4.0379PIC
GB-LIVE32
Gekkio
51.4 × 61 mm46 parts4LCC-BY-4.0379PIC
GB-CART256K-A
Gekkio
51.4 × 61 mm17 parts2LCC-BY-4.0379