SYS StepAtten

schilkp·SYS_StepAtten·KiCad/SYS_StepAtten/SYS_StepAtten.kicad_pcb

SYS StepAtten PCB layout, top view — open source STM32 board by schilkp

About the SYS StepAtten PCB

SYS StepAtten is an open source STM32 PCB design by schilkp, published on GitHub under the MIT license. It is a 2-layer board measuring 122 × 84 mm, with 142 components from 58 distinct parts.

Its main chip is the STM32f030K6T6, from the STM32 family. Other key parts include the LM317 and MC34063AD. By type, the board carries 58 resistors, 20 diodes, 14 transistors, 14 relays, 13 capacitors and 12 connectors.

From the project

A 127 Step Relay Step-Attenuator and 4-way input switcher designed to fit into a Schiit SYS enclosure.

A 127 Step Relay Step-Attenuator and 4-way input switcher designed to fit into a Schiit SYS enclosure.

A remote consists of a potentiometer between 3V and GND with wiper connected to 'Poti' A 10K resistor has to be placed between GND and Sense for the remote to be detected. If the remote features a switch, it should short Sense to GND.

The SYS is normally fitted with a toggle switch (ALPS SPUN191400), but a momentary version of that switch also exists (ALPS SPUN190900).

SYS StepAtten, from the project README
From the project README

Main components on the SYS StepAtten

SYS StepAtten bill of materials (BOM)

142 components, 58 distinct parts.

QtyPartRefs
1
LM317
U1
1
MC34063AD
U2
1
STM32f030K6T6
U4
14
2N7002
Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 +6
1
RCA-Out
J1
1
RCA-1
J2
1
RCA-2
J3
1
AUX-1-2
J4
1
Barrel_Jack 9Vdc
J5
1
POT_EXT Conn
J6
1
cfg jumper
J7
1
ARM SWD
J8
2
A/D GND Jumper
J9, J10
1
ADJ_L
J11
1
ADJ_R
J12
1
1A
F1
1
0.15A
F2
1
BarrelPolarity_CenterPos
G1
1
gnd_case
JP1
14
TQ2SA
K1, K2, K3, K4, K5, K6, K7, K8 +6
Show 38 more
QtyPartRefs
1
10K Linear
RV1
1
INPUT_SWITCH
SW1
1
ON/OFF
SW2
1
1N5819
D1
4
SD03
D3, D4, D6, D7
14
1N4001
D5, D11, D12, D13, D14, D15, D16, D17 +6
1
LED_RGBA
D10
1
22uH/800mA
L1
8
0u1
C1, C2, C4, C8, C10, C13, C14, C16
1
1000u
C3
1
1uf
C5
1
47pf
C6
1
470u
C7
1
1u
C15
14
10K
R1, R17, R34, R35, R36, R37, R40, R41 +6
2
100R
R2, R3
4
1K
R4, R5, R6, R7
1
1K5
R8
2
261R
R9, R10
2
9K53
R11, R12
2
1K87
R13, R14
2
8K25
R15, R16
2
6K49
R18, R19
2
5K9
R20, R21
2
18K
R22, R23
2
3K6
R24, R25
2
39K
R26, R27
2
2K
R28, R29
2
82K
R30, R31
2
1K1
R32, R33
2
160K
R38, R39
2
560R
R42, R43
2
0R
R48, R49
2
12K
R50, R52
2
5K
R51, R53
1
0R33 / 0.5W min
R54
1
3K8
R55
1
1K2
R56

SYS StepAtten design files

The KiCad project lives in the schilkp/SYS_StepAtten repository on GitHub; these links point at the commit this page was built from.

SYS StepAtten: common questions

What microcontroller does the SYS StepAtten use?

The SYS StepAtten is built around the STM32f030K6T6, from the STM32 family.

How big is the SYS StepAtten PCB?

The SYS StepAtten measures 122 × 84 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the SYS StepAtten?

142 components, from 58 distinct parts. The full bill of materials is listed on this page.

Where can I download the SYS StepAtten design files?

From the schilkp/SYS_StepAtten repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the SYS StepAtten design in my own project?

Yes, under the terms of its MIT license, which schilkp chose for the repository.

Can I test firmware for the SYS StepAtten without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards