Dplayer swift v3.1
schoetec·SwiftSqueakBox·SwiftSqueakBox/dplayer_swift_v3.1/dplayer_swift_v3.1.kicad_pcb
About the Dplayer swift v3.1 PCB
Dplayer swift v3.1 is an open source AVR/Arduino PCB design by schoetec, published on GitHub under the MIT license. It is a 2-layer board measuring 63.7 × 40.8 mm, with 15 components from 14 distinct parts.
Its main chip is the ATtiny85-20P, from the AVR/Arduino family. Other key parts include the dfplayer. By type, the board carries 6 connectors, 3 resistors, 2 ICs, 1 switch, 1 diode and 1 capacitor.
From the project
A box to make Swift Squeak noise if asked to make these sounds.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
Main components on the Dplayer swift v3.1
Dplayer swift v3.1 bill of materials (BOM)
15 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATtiny85-20P | DIP-8_W7.62mm | U1 |
| 1 | dfplayer | DFPlayer | U2 |
| 1 | ADKEY | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J2 |
| 1 | DAC | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J3 |
| 1 | BUSY | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J4 |
| 1 | LS | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J5 |
| 1 | Power | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J6 |
| 1 | MUTE | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J7 |
| 1 | 10K | Potentiometer_Piher_PT-10-V10_Vertical | RV1 |
| 1 | Reset | SW_PUSH_6mm_H4.3mm | SW2 |
| 1 | LED | LED_D3.0mm | D1 |
| 1 | 0.1uf | C_Rect_L4.6mm_W2.0mm_P2.50mm_MKS02_FKP02 | C1 |
| 1 | 10K | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 2 | 1K | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R3 |
Dplayer swift v3.1 design files
The KiCad project lives in the schoetec/SwiftSqueakBox repository on GitHub; these links point at the commit this page was built from.
Dplayer swift v3.1: common questions
What microcontroller does the Dplayer swift v3.1 use?
The Dplayer swift v3.1 is built around the ATtiny85-20P, from the AVR/Arduino family.
How big is the Dplayer swift v3.1 PCB?
The Dplayer swift v3.1 measures 63.7 × 40.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Dplayer swift v3.1?
15 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Dplayer swift v3.1 design files?
From the schoetec/SwiftSqueakBox repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Dplayer swift v3.1 design in my own project?
Yes, under the terms of its MIT license, which schoetec chose for the repository.
Can I test firmware for the Dplayer swift v3.1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in SwiftSqueakBox
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k