Scorpion PDB v1.0
shahidkhan-786·Scorpion_PDB_v1.0
About the Scorpion PDB v1.0 PCB
Scorpion PDB v1.0 is an open source ESP32 PCB design by shahidkhan-786, published on GitHub. It is a 2-layer board measuring 66.5 × 32.5 mm, with 24 components from 15 distinct parts.
Its main chip is the To ESp32, from the ESP32 family. Other key parts include the TPS563200DDC. By type, the board carries 7 connectors, 5 resistors, 1 IC, 1 diode and 1 inductor.
It belongs with the robotics & motion and power & battery designs in this gallery.
From the project
This is a Buck Converter, which outputs 5v
I am making a Buck converter. I am making it using a TPS563200 Chip...I used ths because it is Small, Cheap, and Reliable to output 3A Current.
This is my schematic...I mostly referred to DataSheet of TPS563200.
This is the Layout/Routing part...I think this was the hardest part of the project, since the DataSheet gave very strict instructions for this.
Hopefully after soldering all components it look like this.
Main components on the Scorpion PDB v1.0
Scorpion PDB v1.0 bill of materials (BOM)
24 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS563200DDC | SOT-23-6 | U1 |
| 7 | Conn_01x02_Pin | TestPoint_2Pads_Pitch5.08mm_Drill1.3mm | J1, J2, J3, J4, J5, J6, J7 |
| 1 | + | TestPoint_Plated_Hole_D3.0mm | Bat_in1 |
| 1 | - | TestPoint_Plated_Hole_D3.0mm | Bat_in2 |
| 1 | 0.1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | Cboot1 |
| 2 | 10uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | Cin1, Cin2 |
| 2 | 22uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | Cout1, Cout2 |
| 1 | 1000uF | CP_Radial_D10.0mm_P5.00mm | Cstabalizer1 |
| 1 | To ESp32 | TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | VoltageMeter1 |
| 1 | LED | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | 4.7uH | L_10.4x10.4_H4.8 | L1 |
| 1 | 56K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1 |
| 2 | 10K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2, R4 |
| 1 | 33K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3 |
| 1 | 1K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R5 |
Scorpion PDB v1.0 design files
The KiCad project lives in the shahidkhan-786/Scorpion_PDB_v1.0 repository on GitHub; these links point at the commit this page was built from.
Scorpion PDB v1.0: common questions
What microcontroller does the Scorpion PDB v1.0 use?
The Scorpion PDB v1.0 is built around the To ESp32, from the ESP32 family.
How big is the Scorpion PDB v1.0 PCB?
The Scorpion PDB v1.0 measures 66.5 × 32.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Scorpion PDB v1.0?
24 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Scorpion PDB v1.0 design files?
From the shahidkhan-786/Scorpion_PDB_v1.0 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Scorpion PDB v1.0 design in my own project?
The repository has no license, so all rights stay with shahidkhan-786. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Scorpion PDB v1.0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k