Ee portfolio
shonzinger-spec·ee-portfolio·02-sync-buck/hw/kicad/sync_buck.kicad_sch

About the Ee portfolio PCB
Ee portfolio is an open source ESP32 PCB design by shonzinger-spec, published on GitHub under the MIT license. It is a board, with 33 components from 23 distinct parts.
Its main chip is the ESP32 DevKit, from the ESP32 family. Other key parts include the UCC27211 and INA181A3. By type, the board carries 13 resistors, 12 capacitors, 3 connectors, 2 ICs, 2 transistors and 1 inductor.
It belongs with the power & battery designs in this gallery.
From the project
Electrical engineering portfolio: simulated and verified EE projects (firmware, SPICE, KiCad, Wokwi) by Shon Zinger
A simulated design of a digitally controlled synchronous buck: 12 V in, 5 V out at up to 3 A, 200 kHz, two discrete 40 V N-MOSFETs driven by a UCC27211 half-bridge driver, 15 uH / 470 uF output filter, RC snubber on the switch node, and an ESP32-class controller closing the loop in C. The controller samples the output (10k / 6.8k divider), the load current (5 mOhm shunt + INA181A3) and the input voltage (47k / 10k divider) at 50 kHz and runs a PI loop on volts with input-voltage and reference feed-forward, an integrator dead band, DPWM hysteresis, anti-windup, a pre-bias-safe soft start and a…
Main components on the Ee portfolio
Ee portfolio bill of materials (BOM)
33 components, 23 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | UCC27211 | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | INA181A3 | SOT-23-6 | U2 |
| 2 | 30V 7mOhm NMOS (generic) | TO-252-3_TabPin2 | Q1, Q2 |
| 1 | VIN 12V | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | VOUT 5V | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | ESP32 DevKit | PinHeader_1x07_P2.54mm_Vertical | J3 |
| 1 | 15uH Isat>=6A DCR 20mOhm | L_Bourns_SRP1245A | L1 |
| 2 | 10uF 25V X7R | C_1210_3225Metric | C1, C2 |
| 1 | 100uF 25V electrolytic | CP_Radial_D8.0mm_P3.50mm | C3 |
| 1 | 1uF 25V | C_0603_1608Metric | C4 |
| 1 | 100nF 50V | C_0603_1608Metric | C5 |
| 1 | 1nF 50V C0G | C_0603_1608Metric | C6 |
| 1 | 470uF 6.3V polymer | CP_Elec_6.3x7.7 | C7 |
| 1 | 10uF 10V X7R | C_0805_2012Metric | C8 |
| 1 | 100nF | C_0603_1608Metric | C9 |
| 3 | 1nF | C_0603_1608Metric | C10, C11, C12 |
| 2 | 2.2R | R_0603_1608Metric | R1, R2 |
| 6 | 10k | R_0603_1608Metric | R3, R4, R7, R10, R11, R13 |
| 1 | 1.8R | R_0603_1608Metric | R5 |
| 1 | 5mOhm 1% | R_Shunt_Vishay_WSK2512_6332Metric_T1.19mm | R6 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 6.8k | R_0603_1608Metric | R8 |
| 1 | 1k | R_0603_1608Metric | R9 |
| 1 | 47k | R_0603_1608Metric | R12 |
Ee portfolio design files
The KiCad project lives in the shonzinger-spec/ee-portfolio repository on GitHub; these links point at the commit this page was built from.
Ee portfolio: common questions
What microcontroller does the Ee portfolio use?
The Ee portfolio is built around the ESP32 DevKit, from the ESP32 family.
How many components are on the Ee portfolio?
33 components, from 23 distinct parts. The full bill of materials is listed on this page.
Where can I download the Ee portfolio design files?
From the shonzinger-spec/ee-portfolio repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Ee portfolio design in my own project?
Yes, under the terms of its MIT license, which shonzinger-spec chose for the repository.
Can I test firmware for the Ee portfolio without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k