Spark4pi sensors-0.02

Slenderman00·spark4pi-sensors·board/spark.kicad_pcb

Spark4pi sensors-0.02 PCB layout, top view — open source Raspberry Pi board by Slenderman00

About the Spark4pi sensors-0.02 PCB

Spark4pi sensors-0.02 is an open source Raspberry Pi PCB design by Slenderman00, published on GitHub under the TAPR-OHL-1.0 license. It is a 4-layer board measuring 198 × 85 mm, with 38 components from 18 distinct parts.

Its main chip is the SSW-120-01-T-D-006, from the Raspberry Pi family. Other key parts include the LD1117S33TR_SOT223. By type, the board carries 18 resistors, 10 connectors, 6 diodes and 1 IC.

It belongs with the sensors designs in this gallery.

From the project

spark4pi-* is a modular hardware platform for managed instrument implementations controlled over Raspberry Pi compatible 40 pin interface. The design is inspired by the Spark hardware platform for networking as form factor but with a Raspberry Pi 40 pin connector as management in

spark4pi-* is a modular hardware platform for managed instrument implementations controlled over Raspberry Pi compatible 40 pin interface. The design is inspired by the Spark hardware platform for networking as form factor but with a Raspberry Pi 40 pin connector as management interface instead of 96boards.

The spark4pi-digital-io has 6x SMA connectors connected to input (3.3V or 1.65V) and output drivers (3.3V or 5V with open-circuit and 1.65V or 2.5V with 50 ohm termination ) with configurable direction that are connected to GPIOs on the Raspberry Pi connector. 2 GPIOs per channel one for…

Main components on the Spark4pi sensors-0.02

Spark4pi sensors-0.02 bill of materials (BOM)

38 components, 18 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
LD1117S33TR_SOT223
U5
1
USB4105-GF-A
RJ45
J1
1
M20-9990246
RJ45
J2
1
M20-9770346
Conn_02x30_Odd_Even
J3
1
M20-9770346
RJ45
J4
3
RJ45
J5, J6, J7
1
PJ1-021-SMT-TR
Barrel_Jack
J8
1
Conn_02x20_Odd_Even
P1
1
SSW-120-01-T-D-006
Raspberry_Pi_2_3
P5
2
—
1, 2
1
lsi-powermodule-7
LSI-U1
6
SML-LX0603GW-TR
LED
D1, D2, D3, D4, D5, D6
1
ERJ-2GEJ102X
4.7k
R1
2
ERJ-2RKF5101X
4.7k
R2, R5
1
CR0402-FX-2200GLF
4.7k
R3
1
CR0402-FX-68R0GLF
4.7k
R4
7
4.7k
R6, R7, R8, R9, R10, R19, R20
6
1K
R13, R14, R15, R16, R17, R18

Spark4pi sensors-0.02 design files

The KiCad project lives in the Slenderman00/spark4pi-sensors repository on GitHub; these links point at the commit this page was built from.

Spark4pi sensors-0.02: common questions

What microcontroller does the Spark4pi sensors-0.02 use?

The Spark4pi sensors-0.02 is built around the SSW-120-01-T-D-006, from the Raspberry Pi family.

How big is the Spark4pi sensors-0.02 PCB?

The Spark4pi sensors-0.02 measures 198 × 85 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Spark4pi sensors-0.02?

38 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Spark4pi sensors-0.02 design files?

From the Slenderman00/spark4pi-sensors repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Spark4pi sensors-0.02 design in my own project?

Yes, under the terms of its TAPR-OHL-1.0 license, which Slenderman00 chose for the repository.

Can I test firmware for the Spark4pi sensors-0.02 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

Similar boards