Nostos
snowflake-rider·nostos·docs/schematics/nostos/nostos-wiring.kicad_sch
About the Nostos PCB
Nostos is an open source ESP32 PCB design by snowflake-rider, published on GitHub. It is a board, with 18 components from 16 distinct parts.
Its main chip is the ESP32-S3 BLE MESH BRIDGE, from the ESP32 family. Other key parts include the NUCLEO-F411RE, VS1003B AUDIO DECODER, MPU6050 (RIDER NODE 3, ON) and DHT11 (RIDER NODE 2, ON). By type, the board carries 5 ICs, 4 switches, 4 resistors, 3 diodes and 1 buzzer.
It belongs with the iot & wireless designs in this gallery.
From the project
Group cycling coordination system using STM32F411RE, ESP32-S3, Bluetooth Mesh, and FreeRTOS.
NOSTOS의 현재 핀 정의를 한 장으로 정리한 배선 문서용 KiCad 회로도다. MCU는 STM32 NUCLEO-F411RE, 로직 전압은 3.3V, 모든 모듈은 공통 GND를 기준으로 한다.
- nostos-wiring.kicadpro: KiCad 프로젝트 - nostos-wiring.kicadsch: 편집 가능한 최종 회로도 - Nostos.kicadsym: 프로젝트 전용 심볼 라이브러리 - exports/nostos-wiring.svg: 문서용 벡터 이미지 - exports/nostos-wiring.pdf: 인쇄용 PDF - exports/nostos-wiring.png: 미리보기용 고해상도 PNG - reports/erc.rpt: KiCad ERC 결과 - reports/nostos-wiring.net: 연결 검증용 KiCad 넷리스트 - reports/analysis.json`: 보조 회로 분석 결과
Main components on the Nostos
Nostos bill of materials (BOM)
18 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NUCLEO-F411RE | U1 | |
| 1 | ESP32-S3 BLE MESH BRIDGE | U2 | |
| 1 | VS1003B AUDIO DECODER | U3 | |
| 1 | MPU6050 (RIDER NODE 3, ON) | U4 | |
| 1 | DHT11 (RIDER NODE 2, ON) | U5 | |
| 1 | ACTIVE BUZZER MODULE | BZ1 | |
| 1 | SSD1306 OLED (0x3C) | DS1 | |
| 1 | BTN1 SPEED UP | SW1 | |
| 1 | BTN2 SPEED DOWN | SW2 | |
| 1 | BTN3 STOP REQUEST | SW3 | |
| 1 | BTN4 LOCAL / MSG_NONE | SW4 | |
| 1 | RED | D1 | |
| 1 | GREEN | D2 | |
| 1 | BLUE | D3 | |
| 3 | 330R | R1, R2, R3 | |
| 1 | 10k DHT PULL-UP | R4 |
Nostos design files
The KiCad project lives in the snowflake-rider/nostos repository on GitHub; these links point at the commit this page was built from.
Nostos: common questions
What microcontroller does the Nostos use?
The Nostos is built around the ESP32-S3 BLE MESH BRIDGE, from the ESP32 family.
How many components are on the Nostos?
18 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the Nostos design files?
From the snowflake-rider/nostos repository on GitHub, which has the schematic and a netlist; the links under Design files point to each one.
Can I use the Nostos design in my own project?
The repository has no license, so all rights stay with snowflake-rider. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Nostos without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k