HardLabs

Slider potentiometer breakout qwiic hardware design

SolderedElectronics·Slider-potentiometer-breakout-qwiic-hardware-design·CAD/V1.1.1/Slider_pot_easyC.kicad_pcb

Slider potentiometer breakout qwiic hardware design layout, top view — open source AVR/Arduino board by SolderedElectronics
Simulate this board

About the Slider potentiometer breakout qwiic hardware design

Slider potentiometer breakout qwiic hardware design is an open source AVR/Arduino PCB design by SolderedElectronics, published on GitHub under the TAPR-OHL-1.0 license. It is a 2-layer board measuring 86 × 22 mm, with 15 components from 8 distinct parts.

Its main chip is the ATTINY404-SSNR, from the AVR/Arduino family. By type, the board carries 4 relays, 3 capacitors, 3 resistors and 1 IC.

It belongs with the dev boards & breakouts designs in this gallery.

From the project

Hardware design, BOM, gerbers and 3D files for Slider-potentiometer-breakout-qwiic designed by Soldered Electronics.

Potentiometers are well known all around, and the sliding potentiometer is just one of its versions. You’ve probably seen it in some music equipment, and now you have the chance to add it to your project!

This board has easyC connector. Thanks to easyC ecosystem, this board can be connected using off-the-shelf cables, without soldering. Controlling the is as simple as it gets, too.

Slider potentiometer breakout qwiic hardware design, from the project README
From the project README

Main components on the Slider potentiometer breakout qwiic hardware design

ATTINY404-SSNR

Slider potentiometer breakout qwiic hardware design bill of materials (BOM)

15 components, 8 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATTINY404-SSNR
U1
4
HOLE_3.2mm
H1, H2, H3, H4
2
easyC-SMD
K1, K3
1
HEADER-UPDI
K2
1
DSHP03TS-S
K4
3
0.1uF
C1, C2, C3
1
SLIDER_POT
R1
2
10k
R2, R3

Slider potentiometer breakout qwiic hardware design design files

The KiCad project lives in the SolderedElectronics/Slider-potentiometer-breakout-qwiic-hardware-design repository on GitHub; these links point at the commit this page was built from.

Slider potentiometer breakout qwiic hardware design: common questions

What microcontroller does the Slider potentiometer breakout qwiic hardware design use?

The Slider potentiometer breakout qwiic hardware design is built around the ATTINY404-SSNR, from the AVR/Arduino family.

How big is the Slider potentiometer breakout qwiic hardware design?

The Slider potentiometer breakout qwiic hardware design measures 86 × 22 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Slider potentiometer breakout qwiic hardware design?

15 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Slider potentiometer breakout qwiic hardware design design files?

From the SolderedElectronics/Slider-potentiometer-breakout-qwiic-hardware-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Slider potentiometer breakout qwiic hardware design design in my own project?

Yes, under the terms of its TAPR-OHL-1.0 license, which SolderedElectronics chose for the repository.

Can I test firmware for the Slider potentiometer breakout qwiic hardware design without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards