EasyC ultrasonic adapter

SolderedElectronics·Ultrasonic-sensor-qwiic-hardware-design·CAD/V1.0.0/easyC_ultrasonic_adapter.kicad_pcb

EasyC ultrasonic adapter PCB layout, top view — open source AVR/Arduino board by SolderedElectronics

About the EasyC ultrasonic adapter PCB

EasyC ultrasonic adapter is an open source AVR/Arduino PCB design by SolderedElectronics, published on GitHub under the TAPR-OHL-1.0 license. It is a 2-layer board measuring 22 × 38 mm, with 16 components from 12 distinct parts.

Its main chip is the ATTINY404-SSNR, from the AVR/Arduino family. Other key parts include the TPS613222A. By type, the board carries 5 relays, 4 capacitors, 2 ICs, 2 resistors and 1 inductor.

It belongs with the sensors designs in this gallery.

From the project

Hardware design, BOM, gerbers and 3D files for Ultrasonic-sensor-qwiic designed by Soldered Electronics.

The HC-SR04 ultrasonic sensor is an affordable and super-popular sensor that measures the distance between itself and an object located in front of the sensor. Very simple to use, it returns the distance in centimeters or inches. In this variation, it comes on a board with an Attiny microcontroller that sends readings from the sensor as a digital signal via the qwiic connector to the microcontroller, which makes its connections a piece of cake.

EasyC ultrasonic adapter, from the project README
From the project README

Main components on the EasyC ultrasonic adapter

EasyC ultrasonic adapter bill of materials (BOM)

16 components, 12 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATTINY404-SSNR
U1
1
TPS613222A
U2
2
HOLE_3.2MM
HOLE_3.2mm
H1, H2
1
HEADER_MALE_4X1
K1
2
easyC-SMD
K2, K4
1
HEADER-UPDI
K3
1
DSHP03TS-S
K5
1
DFE201612E-2R2M=P2
L1
1
100N
0.1uF
C1
2
CL10A226MPCNUBE
C2, C3
1
C1608X7S1A475K080AC
C4
2
10K
10k
R1, R2

EasyC ultrasonic adapter design files

The KiCad project lives in the SolderedElectronics/Ultrasonic-sensor-qwiic-hardware-design repository on GitHub; these links point at the commit this page was built from.

EasyC ultrasonic adapter: common questions

What microcontroller does the EasyC ultrasonic adapter use?

The EasyC ultrasonic adapter is built around the ATTINY404-SSNR, from the AVR/Arduino family.

How big is the EasyC ultrasonic adapter PCB?

The EasyC ultrasonic adapter measures 22 × 38 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the EasyC ultrasonic adapter?

16 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the EasyC ultrasonic adapter design files?

From the SolderedElectronics/Ultrasonic-sensor-qwiic-hardware-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the EasyC ultrasonic adapter design in my own project?

Yes, under the terms of its TAPR-OHL-1.0 license, which SolderedElectronics chose for the repository.

Can I test firmware for the EasyC ultrasonic adapter without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in Ultrasonic-sensor-qwiic-hardware-design

Similar boards