Digispark-USB
SoloScriptSage·Digispark-USB
About the Digispark-USB PCB
Digispark-USB is an open source AVR/Arduino PCB design by SoloScriptSage, published on GitHub. It is a 2-layer board measuring 40 × 13.5 mm, with 12 components from 9 distinct parts.
Its main chip is the ATtiny85-20S, from the AVR/Arduino family. By type, the board carries 4 resistors, 3 diodes, 2 ICs, 2 connectors and 1 capacitor.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Custom PCB clone of the Digispark development board — ATtiny85 with USB programming support, designed in KiCad
A custom PCB clone of the Digispark development board — a minimal ATtiny85-based microcontroller board with native USB programming support. Designed from scratch in KiCad.
The original Digispark is a tiny Arduino-compatible board built around the ATtiny85. This is a custom PCB recreation of that design, including the USB low-speed interface circuit for programming directly over USB without a separate programmer.

Main components on the Digispark-USB
Digispark-USB bill of materials (BOM)
12 components, 9 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | PCB_USB_Connector | U1 |
| 1 | ATtiny85-20S | SOIC-8_5.3x5.3mm_P1.27mm | U2 |
| 2 | Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | J1, J2 |
| 2 | 3V6 | D_SOD-123 | D1, D2 |
| 1 | LED | LED_D3.0mm | D3 |
| 1 | 100n | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 2 | 68R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 1 | 330R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | 1k5 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
Digispark-USB design files
The KiCad project lives in the SoloScriptSage/Digispark-USB repository on GitHub; these links point at the commit this page was built from.
- LayoutDigispark USB.kicad_pcb
- SchematicDigispark USB.kicad_sch
Digispark-USB: common questions
What microcontroller does the Digispark-USB use?
The Digispark-USB is built around the ATtiny85-20S, from the AVR/Arduino family.
How big is the Digispark-USB PCB?
The Digispark-USB measures 40 × 13.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Digispark-USB?
12 components, from 9 distinct parts. The full bill of materials is listed on this page.
Where can I download the Digispark-USB design files?
From the SoloScriptSage/Digispark-USB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Digispark-USB design in my own project?
The repository has no license, so all rights stay with SoloScriptSage. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Digispark-USB without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k