BlackBoxProbeBig
Squantor·blackBoxProbe·electronics/blackBoxProbeBig/blackBoxProbeBig.kicad_pcb
About the BlackBoxProbeBig PCB
BlackBoxProbeBig is an open source STM32 PCB design by Squantor, published on GitHub under the MIT license. It is a 4-layer board measuring 44 × 44 mm, with 75 components from 32 distinct parts.
Its main chip is the STM32F103CBT, from the STM32 family. Other key parts include the MCP1702-MB, USBLC6-2 and 74X2T45. By type, the board carries 33 resistors, 21 capacitors, 7 ICs, 4 connectors, 4 diodes and 2 transistors.
From the project
A boxed clone of the black magic probe
Main components on the BlackBoxProbeBig
BlackBoxProbeBig bill of materials (BOM)
75 components, 32 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MCP1702-MB | SOT89-ViaTab-Microchip-MB | U1 |
| 1 | USBLC6-2 | SOT23-6-HAND | U2 |
| 1 | STM32F103CBT | SOT313-2 | U3 |
| 4 | 74X2T45 | SOT765-1-NXP | U4, U5, U6, U7 |
| 1 | Q_NMOS_DUAL | SOT363-hand | Q1 |
| 1 | Q_PMOS_DUAL | SOT363-hand | Q2 |
| 1 | 8.000MHz | X_5.0_3.2 | Y1 |
| 1 | USB-ID | SquantorUsb-USB-UB-SMD4H | J1 |
| 1 | JTAG_2X05 | Header-0127-2X05-H006 | J2 |
| 1 | JTAG_2X05 | Header-Shr-0127-2X05-H006 | J3 |
| 1 | Conn_01x04 | Pin_Header_Angled_1x04_Pitch2.54mm | J4 |
| 1 | V20181130 | Label_version | N2 |
| 1 | BlackBoxProbe | Label_version | N3 |
| 1 | 2pin_tact_switch | DTSM3 | S1 |
| 1 | Green | LED_D3.0mm | D1 |
| 1 | Yellow | LED_D3.0mm | D2 |
| 1 | Orange | LED_D3.0mm | D3 |
| 1 | Red | LED_D3.0mm | D4 |
| 1 | 1u | C_0603 | C1 |
| 1 | 100N | C_0805 | C2 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 10u | C_0805 | C4, C9, C14 |
| 14 | 100n | C_0603 | C5, C6, C7, C8, C10, C11, C15, C16 +6 |
| 2 | 10p | C_0603 | C12, C13 |
| 1 | FB | R_0603_hand | R1 |
| 2 | R | R_0603_hand | R4, R5 |
| 7 | 10K | R_0603_hand | R6, R11, R12, R20, R28, R37, R38 |
| 2 | 4.7K | R_0603_hand | R7, R10 |
| 12 | 100 | R_0603_hand | R8, R9, R13, R14, R15, R21, R22, R24 +4 |
| 1 | 1.5K | R_0603_hand | R16 |
| 1 | 47K | R_0603_hand | R18 |
| 3 | 22 | R_0603_hand | R27, R34, R36 |
| 4 | 330 | R_0603_hand | R29, R30, R31, R32 |
BlackBoxProbeBig design files
The KiCad project lives in the Squantor/blackBoxProbe repository on GitHub; these links point at the commit this page was built from.
BlackBoxProbeBig: common questions
What microcontroller does the BlackBoxProbeBig use?
The BlackBoxProbeBig is built around the STM32F103CBT, from the STM32 family.
How big is the BlackBoxProbeBig PCB?
The BlackBoxProbeBig measures 44 × 44 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the BlackBoxProbeBig?
75 components, from 32 distinct parts. The full bill of materials is listed on this page.
Where can I download the BlackBoxProbeBig design files?
From the Squantor/blackBoxProbe repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the BlackBoxProbeBig design in my own project?
Yes, under the terms of its MIT license, which Squantor chose for the repository.
Can I test firmware for the BlackBoxProbeBig without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in blackBoxProbe
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k