Arduino water level monitor
Srushti-D-Hebbar·arduino-water-level-monitor·hardware/water_level.kicad_pcb
About the Arduino water level monitor PCB
Arduino water level monitor is an open source AVR/Arduino PCB design by Srushti-D-Hebbar, published on GitHub under the MIT license. It is a 2-layer board measuring 88.6 × 78.8 mm, with 19 components from 16 distinct parts.
Its main chip is the Arduino_UNO_R3, from the AVR/Arduino family. Other key parts include the HC-SR04. By type, the board carries 4 capacitors, 4 resistors, 3 connectors, 2 ICs, 2 switches and 1 transistor.
It belongs with the displays & leds and iot & wireless designs in this gallery.
From the project
Arduino Uno water-level monitoring and pump controller with HC-SR04, 16×2 LCD, and relay-based pump control. Wokwi-validated and designed as a 2-layer PCB in KiCad 10.
An Arduino Uno–based water tank level monitor with automatic pump control, built and simulated in Wokwi, then converted into a full KiCad 10 PCB design.
The system uses an ultrasonic sensor to measure water level, displays the percentage on a 16x2 LCD, and switches a pump on/off through a relay — either automatically based on level thresholds, or manually via a pushbutton.

Main components on the Arduino water level monitor
Arduino water level monitor bill of materials (BOM)
19 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Arduino_UNO_R3 | Arduino_UNO_R3 | U1 |
| 1 | HC-SR04 | PinHeader_1x04_P2.54mm_Vertical | U2 |
| 1 | 2N2219 | TO-39-3 | Q1 |
| 1 | Conn_01x16_Pin | PinHeader_1x16_P2.54mm_Vertical | J2 |
| 1 | RELAY_OUT | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | POWER_IN | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | SANYOU_SRD_Form_C | Relay_SPDT_SANYOU_SRD_Series_Form_C | K1 |
| 1 | 10k | Potentiometer_Bourns_3224J_Horizontal | RV1 |
| 1 | SET | SW_SPST_B3S-1000 | SW1 |
| 1 | AUTO/MANUAL | SW_SPST_B3S-1000 | SW2 |
| 1 | 1N4007 | D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 2 | 100nF | C_0805_2012Metric | C1, C3 |
| 2 | 10uF | C_1206_3216Metric | C2, C4 |
| 1 | 1k | R_0805_2012Metric | R1 |
| 1 | 220R | R_0805_2012Metric | R3 |
| 2 | 10k | R_0805_2012Metric | R4, R5 |
Arduino water level monitor design files
The KiCad project lives in the Srushti-D-Hebbar/arduino-water-level-monitor repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/water_level.kicad_pcb
- Schematichardware/water_level.kicad_sch
Arduino water level monitor: common questions
What microcontroller does the Arduino water level monitor use?
The Arduino water level monitor is built around the Arduino_UNO_R3, from the AVR/Arduino family.
How big is the Arduino water level monitor PCB?
The Arduino water level monitor measures 88.6 × 78.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Arduino water level monitor?
19 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the Arduino water level monitor design files?
From the Srushti-D-Hebbar/arduino-water-level-monitor repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Arduino water level monitor design in my own project?
Yes, under the terms of its MIT license, which Srushti-D-Hebbar chose for the repository.
Can I test firmware for the Arduino water level monitor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k