Zynq sdr dongle
SunnyYoshimitsu·SideKick·hardware/zynq_sdr_dongle.kicad_pcb
About the Zynq sdr dongle PCB
Zynq sdr dongle is an open source FPGA PCB design by SunnyYoshimitsu, published on GitHub under the GPL-3.0 license. It is a 6-layer board measuring 75.3 × 94.2 mm, with 277 components from 62 distinct parts.
Its main chip is the xc7z020clg400, from the FPGA family. Other key parts include the DDR3, AD9361, TPS62088, USB3346 and MAX38904C. By type, the board carries 148 capacitors, 71 resistors, 17 inductors, 14 connectors, 12 ICs and 5 diodes.
It belongs with the rf & radio designs in this gallery.
From the project
WIP, FPGA Based Phone
Main components on the Zynq sdr dongle
Zynq sdr dongle bill of materials (BOM)
277 components, 62 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DDR3 | BGA-96_9.0x13.0mm_Layout2x3x16_P0.8mm_NoPaste | U1 |
| 1 | xc7z020clg400 | Xilinx_CLG400_020_Delay | U2 |
| 1 | AD9361 | bga-100_10_10_1p32_0p8 | U3 |
| 3 | TPS62088 | PowerWCSP-6 | U4, U9, U10 |
| 1 | USB3346 | QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U5 |
| 2 | MAX38904C | wlp-15_2p168_1p338_0p5_0p4 | U6, U7 |
| 1 | TPS62867 | VQFN-HR | U8 |
| 1 | TPS2121 | VQFN-12_2p0_2p5_0p5 | U11 |
| 1 | TXS0206A | WLCSP-20_1.609x1.994mm_Layout4x5_P0.4mm | U13 |
| 1 | Q_Dual_NMOS_PMDXB600UNE | DFN-6-1EP_1.2x1.2mm_P0.4mm_EP0.3x0.94mm_PullBack | Q1 |
| 1 | PMCM4401VNE | WLCSP-4-X1-WLB0909-4_0.89x0.89mm_P0.5mm | Q2 |
| 3 | SiT1602B | Oscillator_SMD_ECS_2520MV-xxx-xx-4Pin_2.5x2.0mm | X1, X2, X3 |
| 1 | USB_C_Receptacle | USB_C_Receptacle_Amphenol_12401548E4-2A_CircularHoles | J1 |
| 1 | USB_B_Micro | USB_Micro-B_Amphenol_10104110_Horizontal | J2 |
| 1 | Micro_SD_Card | microSD_HC_Molex_104031-0811 | J3 |
| 1 | 5024268012 | Molex_SlimStack_502430-8010_2x40_P0.40mm_Vertical | J4 |
| 6 | Conn_Coaxial | U.FL_Molex_MCRF_73412-0110_Vertical | J5, J6, J7, J8, J9, J12 |
| 1 | Conn_01x13_Male | PinHeader_1x13_P2.54mm_Vertical | J10 |
| 1 | DNP Conn_01x16_Male | PinHeader_1x16_P2.54mm_Vertical | J11 |
| 1 | Conn_01x04_Male | BM03B-ACHSS-GAN-TF | J13 |
Show 42 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Conn_01x01 | PinHeader_1x01_P2.54mm_Vertical | J14 |
| 4 | 0850BM14E0016 | Balun_Johanson_1.6x0.8mm | FL1, FL2, FL3, FL4 |
| 1 | SW_DIP_x01 | EVQ9P701P | SW2 |
| 3 | LED | LED_0201_0603Metric | D1, D2, D3 |
| 2 | TVS | R_0201_0603Metric | D4, D5 |
| 2 | FerriteBead_Small | C_0402_1005Metric | FB1, FB9 |
| 7 | FerriteBead_Small | C_0201_0603Metric | FB2, FB3, FB4, FB5, FB6, FB7, FB8 |
| 4 | DFE18SANR47MG0 | L_Murata_LQH2MCNxxxx02_2.0x1.6mm | L1, L6, L7, L8 |
| 4 | L | L_0402_1005Metric | L2, L3, L4, L5 |
| 6 | 18pF | C_0201_0603Metric | C1, C6, C9, C12, C80, C81 |
| 15 | 0.1uF | C_0402_1005Metric | C2, C10, C13, C22, C28, C29, C36, C41 +7 |
| 85 | 0.1uF | C_0201_0603Metric | C3, C4, C5, C7, C8, C11, C14, C15 +77 |
| 29 | 4.7uF | C_0402_1005Metric | C23, C27, C30, C32, C35, C37, C39, C40 +21 |
| 6 | NFM15PC146R0G3D | C_0402_1005Metric | C82, C104, C105, C112, C113, C114 |
| 3 | 1uF | C_0402_1005Metric | C103, C106, C129 |
| 4 | 10nF | C_0402_1005Metric | C121, C122, C126, C127 |
| 3 | 80Ω | R_0201_0603Metric | R1, R4, R5 |
| 8 | 4.7K | R_0201_0603Metric | R2, R47, R48, R55, R56, R59, R70, R71 |
| 2 | 240Ω | R_0201_0603Metric | R3, R43 |
| 2 | 23.7K | R_0201_0603Metric | R6, R37 |
| 3 | 5K | R_0201_0603Metric | R7, R30, R38 |
| 12 | 10K | R_0201_0603Metric | R8, R19, R22, R25, R46, R49, R50, R52 +4 |
| 1 | 82K | R_0201_0603Metric | R9 |
| 1 | 18K | R_0201_0603Metric | R10 |
| 3 | 14.3K | R_0201_0603Metric | R11, R12, R18 |
| 2 | 360K | R_0201_0603Metric | R13, R15 |
| 2 | 300K | R_0201_0603Metric | R14, R16 |
| 1 | 8.06K | R_0201_0603Metric | R17 |
| 1 | 200K | R_0201_0603Metric | R20 |
| 1 | 100K | R_0201_0603Metric | R21 |
| 1 | 51.7K | R_0201_0603Metric | R23 |
| 1 | 41.2K | R_0201_0603Metric | R24 |
| 1 | 22K | R_0201_0603Metric | R26 |
| 1 | 33K | R_0201_0603Metric | R27 |
| 4 | 0R | R_0201_0603Metric | R28, R53, R64, R67 |
| 1 | 10.2K | R_0201_0603Metric | R29 |
| 7 | 1K | R_0201_0603Metric | R31, R32, R33, R34, R35, R36, R40 |
| 1 | 51.1K | R_0201_0603Metric | R39 |
| 1 | 0R | R_0402_1005Metric | R41 |
| 7 | N/A | R_0201_0603Metric | R42, R51, R54, R60, R61, R63, R68 |
| 2 | 500Ω | R_0201_0603Metric | R44, R45 |
| 2 | 30R | R_0201_0603Metric | R57, R58 |
Zynq sdr dongle design files
The KiCad project lives in the SunnyYoshimitsu/SideKick repository on GitHub; these links point at the commit this page was built from.
Zynq sdr dongle: common questions
What microcontroller does the Zynq sdr dongle use?
The Zynq sdr dongle is built around the xc7z020clg400, from the FPGA family.
How big is the Zynq sdr dongle PCB?
The Zynq sdr dongle measures 75.3 × 94.2 mm, has 6 copper layers and is 1.217 mm thick.
How many components are on the Zynq sdr dongle?
277 components, from 62 distinct parts. The full bill of materials is listed on this page.
Where can I download the Zynq sdr dongle design files?
From the SunnyYoshimitsu/SideKick repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Zynq sdr dongle design in my own project?
Yes, under the terms of its GPL-3.0 license, which SunnyYoshimitsu chose for the repository.
Can I test firmware for the Zynq sdr dongle without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug FPGA firmware against it before you order a PCB.
More boards in SideKick
Similar boards
FPGA
Base board
GlasgowEmbedded
80 × 49 mm222 parts4L0BSD2.2kFPGA
Thunderscope Rev5.3
EEVengers
122.5 × 103.5 mm817 parts6LMIT1.3kFPGA
Usb sniffer
ataradov
58.2 × 38.1 mm86 parts2LBSD-3-Clause1.3kFPGA
Tomu, I'm
theacodes
13 × 9.4 mm40 parts4LMIT1.1kFPGA
Icepi zero
cheyao
65 × 30 mm143 parts4LSHL-2.1865FPGA
Gcvideo
ikorb
49 × 30 mm44 parts4LNo license765